Bailey Dennis

My duties as an operator technician at Williams consists of the following:

• Meeting customers expectation by keeping engines running to continue the flow of natural gas through the pipeline.
• Maintenance on valves, pumps, compressors, instruments, and other equipment used around the compressor station and valve sites.
• Orientating contractors on our facility.
• Writing general work permits along with confined space, hot work, LOTO, disable and bypass safety devices, critical lift, electrical safety, excavation and trenching, and JSA.
• Handle projects such as anomaly digs, pipe replacements, valve replacements, and installing new interconnects.
• Responding to one calls and locating buried pipelines.
• Going online with the station PLC to toggle bits for device testing and to troubleshoot in the logic.
• Testing, calibrating, repairing, and installing unit and station devices such as pneumatic switches, pressure, flow, temperature, and level transmitters, speed switches, thermocouples, vibration switches, I/P converters, and relief valves.
• Checking clearances on piston, articulating, and compressor rod bearings.
• Operating different systems at the station such as coolant, oil, fuel gas, power gas, ESD, EBD, and instrument air systems.
• Test and calibrate ultrasonic and orifice flow meters.
• Collect gas samples.
• Pull stain tubes.
• Inspecting tanks, containments, and hazardous waste areas.
• Sampling oil and coolant.
• Using maximo to complete preventive and corrective work orders, generate new work request, submit concern reports, and submit after-the-fact work orders.
• Provided on-the-job training to newly hired workers and team members.
• Maintained knowledge of industry policies and procedures to set up and operate equipment safely.
• Upheld strict compliance with applicable industry standards for preventive and corrective maintenance.
• Cultivated interpersonal skills by building positive relationships with others.
• Gained strong leadership skills by managing projects from start to finish.
• Skilled at working independently and collaboratively in a team environment.

ISC had the maintenance contract for Westlake Chemical at the time that I was working for them. I worked in the Poly III and Styrene units. My duties were as listed:

• Perform preventive and corrective maintenance according to work orders received.
• Calibrate, test, and install various instruments including pressure, temperature, level, and flow transmitters, turbidity meters, PH analyzers, hydrocarbon analyzers, fire and gas detectors, and O2 analyzers.
• Interpreted equipment manuals and schematics to determine corrective actions for repairs, calibrations, and installations.
• Performed repair procedures on damaged instruments and sourced replacements from approved vendors.
• Interpreted and utilized wiring diagrams and technical specific instructions to configure instrumentation devices.

While working for IES we worked at LBC Baton Rouge LLC in St. Gabriel and Westlake Chemical South Plant in Sulphur. My duties were as listed:

• Installed new transmitters.
• Installed electrical conduit and wiring for power, controls, and lighting.
• Replaced cable tray.
• Disconnected and removed motors and pumps.
• Interpreted blueprints, schematics, drawings, and layouts to complete repairs.
• Tested wiring and other system parts for electrical flow and function.

Zachry had the maintenance contract at Cheniere LNG during the time that I worked for them. My duties were as listed:

• Tested, inspected, replaced, and calibrated instruments on the fire and gas system.
• Disconnected and installed the instrumentation on the turbines when they would remove the turbines from the turbine packages.
• Tested vibration switches on the fin fans.
• Tested H2S detectors.
• Tested and calibrated PH analyzers.
• Interpreted equipment manuals and schematics to determine corrective actions for repairs, calibrations, and installations.
• Performed repair procedures on damaged instruments and sourced replacements from approved vendors.

During my time with ISC, we worked at Sasol on a new construction project. My duties were as listed:

• Fabricate and install tubing tray and instrument tubing.
• Install various different instruments.
• Perform point-to-point tests on electrical loops according to the loop sheets.
• Update and redline wiring diagrams.

While attending college at Sowela Technical Community College I worked part time, and full time inbetween semesters, at Lake Area Electric. My duties consisted of:

• Performed complete rough-in and trim-outs on custom and spec homes.
• Demonstrated expertise in use of cable reels, stripping tools, voltage detectors, and wire and cable cutters to complete fast-paced work.
• Read and interpreted electrical, mechanical, and architectural drawings and electrical code specifications for wiring layouts.
• Coordinated with other trades and general contractors to facilitate layout of recessed fixtures and architectural lighting.
• Worked from ladders, scaffolds and lifts to install, maintain, or repair electrical wiring equipment and lighting fixtures in ceilings, on roofs and on towers.
• Planned layout and installation of electrical wiring, equipment, and fixtures based on specifications and applicable code.
• Inspected worksites and installations to verify compliance with state safety codes.
• Installed and wired service panels and circuit breakers.