Brett Warner
Glenpool,OK
Summary
A self driven employee seeking a position that values innovation, change, and safe work practices. One where thoughtful ideas are executed and valued.
Overview
19
19
years of professional experience
Work History
Technical Service Engineer
HF Sinclair
05.2015 - Current
- Mentoring junior engineers with basic engineering tasks, including deciphering equipment documentation and basic specs
- Responsible for day to day optimization on many units. These included an FCC, Alky, NHT, DHTU, WWTP.
- Key contact for PRV and Relief System Study. Generated work scope for current and ongoing studies.
- Key contact in major FCC revamp project. Point man on catalyst reformulations and catalyst changes in a majority of covered units.
Senior Process Engineer
Solvay Specialty Polymers
01.2015 - 05.2015
- Reduced downtime for screening Quench PPS by adding an acetic acid addition system to solvent recovery. This more than doubled screening rate and reduced dryer cleanouts from 2x per year to every third year.
- Worked with R/D engineers to install and prove Raman spectrometers in PPS Reactors.
- Optimized screening mesh and material to increase lifetime of screens.
Process Engineer
Chevron Phillips Chemical
01.2005 - 12.2014
- Responsible for day to day optimization of Ryton production.
- Tracked feedstock and ordering long lead chemicals, specifically pDCB. NaSH, and membrane grade NaOH.
- Responsible for process critical changes, including upgrading filter cloths, increased NMP recovery through steam optimization and batch distillation optimizations .
- Day to day analysis of process data with immediate troubleshooting and recommendation generation.
Education
Bachelor of Science - Chemical Engineering
Iowa State University
Ames, IA12.2004
Skills
- Proficient with MS Office Products, specifically Excel, Word, and Powerpoint
- Proficient with process simulation software Specific experience with Aspen Plus and Hsysy Modeling
- Proficient with PS PPM Software used in PRV Modeling
- Trained on Cause Map Analysis
- PHA Participant with 2 occurring under LOPA at CPChem and 3-4 at HFS without LOPA consideration
Additional Information
- NMP savings from CPChem optimization estimate at $1 MM per year in 2007.
- Dehydrator batch distillation revamp added approximately $7 MM dollars of increased production margin in 2012.
- Acid addition to Quench process increased on stream factor by 30%. Estimate value of $30-40 MM per year.
- Batch acid vapor scrubber and recovery system was able to keep new tanks in compliance at HF Sinclair in 2016.
- Water softening saved $2 MM dollars per year of downtime at the FCC unit.
- Reformulation of FCC catalyst allowed unit charge rates of 28-30 MBPD. Approximate $3 MM year of value.
- Penex dryer optimizations led to increased catalyst life. Life expectancy increased by 200% leading to saving of $1 MM per year.
Timeline
Technical Service Engineer
HF Sinclair
05.2015 - Current
Senior Process Engineer
Solvay Specialty Polymers
01.2015 - 05.2015
Process Engineer
Chevron Phillips Chemical
01.2005 - 12.2014
Bachelor of Science - Chemical Engineering
Iowa State University
Similar Profiles
Phil ParkinsonPhil Parkinson
Maintenance Supervisor at Sinclair Casper Refining, HF SinclairMaintenance Supervisor at Sinclair Casper Refining, HF Sinclair
Troy SloanTroy Sloan
Terminal Spervisor III at HF Sinclair MidstreamTerminal Spervisor III at HF Sinclair Midstream
Spencer A. ThompsonSpencer A. Thompson
Industrial Hygienist (Intern) at HF SinclairIndustrial Hygienist (Intern) at HF Sinclair
Jacob Landon WalkerJacob Landon Walker
Process Plant Operator at HF Sinclair RefineryProcess Plant Operator at HF Sinclair Refinery
James TrentJames Trent
Sales Associate at Mark Allen ChevroletSales Associate at Mark Allen Chevrolet