Bruce Nowicki

• Improved equipment efficiency by performing regular maintenance and troubleshooting complex electrical issues.
• Enhanced workplace safety through diligent inspection and repair of electrical systems, reducing incidents of injury.
• Collaborated with engineers and other technicians for the successful completion of various industrial projects.
• Expedited production schedules by promptly addressing electrical malfunctions in a timely manner.
• Upgraded outdated wiring systems to enhance performance and reduce potential hazards in the workplace.

new commercial construction

Lighting and panel terminations,wire pulls and receptacle outlets

• Improved equipment efficiency by performing regular maintenance and troubleshooting complex electrical issues.
• Enhanced workplace safety through diligent inspection and repair of electrical systems, reducing incidents of injury.
• Upgraded outdated wiring systems to enhance performance and reduce potential hazards in the workplace.
• Connected wires to circuit breakers, transformers and other components.
• Repaired and replaced equipment, electrical wiring and fixtures.
• Tested circuit continuity to determine electrical compatibility and component safety.

• Collaborated with engineers and other technicians for the successful completion of various industrial projects.
• Enhanced workplace safety through diligent inspection and repair of electrical systems, reducing incidents of injury.
• Performed thorough testing on newly-installed electrical systems to confirm proper function before integrating into daily operations.

• Improved equipment efficiency by performing regular maintenance and troubleshooting complex electrical issues.
• Enhanced workplace safety through diligent inspection and repair of electrical systems, reducing incidents of injury.
• Diagnosed root causes of equipment failure utilizing advanced diagnostic tools and techniques, enabling swift resolution for minimal disruption to production schedules.
• Followed blueprints to install wiring before completion of walls, ceilings or floors.
• Repaired and replaced equipment, electrical wiring and fixtures.
• Tested circuit continuity to determine electrical compatibility and component safety.
• Attached power cables to equipment such as electric range and motor.

• Improved project efficiency by expertly installing and maintaining electrical systems for commercial and industrial clients.
• Ensured safety compliance by conducting thorough inspections of electrical installations and promptly addressing any issues found.
• Reduced downtime through efficient troubleshooting and repair of complex electrical system malfunctions.
• Enhanced system performance with the installation and configuration of advanced control panels, circuit breakers, and transformers.

*Power plant cable pulls & terminations

* Grounding cad welds for structural grids

• Observed company safety rules and regulations to minimize workplace accidents and reduce electric shocks.

*Upgrade New-Mcc-terminations

*RTD terminations

*Conduit bends & cable tray installations

* 350 to 500 MCM cable pulls

• Maintained solid safety record with no OSHA-recordable incidents.

*Demolition off old motor control center-remove wire & conduit

• Operated tools according to prescribed safety practices.
• Repaired or replaced wiring, equipment and fixtures using hand tools and power tools.

*Add new lighting to steel mill bay area

* reconstruction of cooling tower

*Cable pulls & terminations to Motors

* Conduit bends & runs

• Reduced downtime through efficient troubleshooting and repair of complex electrical system malfunctions.

* High Voltage pulls

* Transformer terminations

* Grid grounds on equipment

* installation of instruments

* Running temporary power

* Installing new heat trace panels on fly ash silos

* Conduit bends & wire pulls

• Ensured safety compliance by conducting thorough inspections of electrical installations and promptly addressing any issues found.

* Commercial Electric for Air Port hanger (Gulf Stream Airospace

* Conduit bends & wire terminations

• Improved project efficiency by expertly installing and maintaining electrical systems for commercial and industrial clients.
• Performed maintenance and reconducting work in varied weather conditions.

* Tank control installations & RTD's

• Improved equipment efficiency by performing regular maintenance and troubleshooting complex electrical issues.

* Cleaning & racking I/O Buss breakers

* High Voltage Stress Cones

• Installed, maintained and repaired electrical wiring, controls and lighting systems.
• Inspected transformers and circuit breakers for malfunctions.
• Attached power cables to equipment such as electric range and motor.

* Industrial & Commercial Electric

*Installation of all power to pumps & motors for Bass Pro Shop

* Installed outdoor lighting

• Performed thorough testing on newly-installed electrical systems to confirm proper function before integrating into daily operations.
• Repaired and replaced equipment, electrical wiring and fixtures.
• Connected wires to circuit breakers, transformers or other components.

• Installed, maintained and repaired electrical wiring, controls and lighting systems.
• Tested electrical systems functionality and continuity of circuits using devices such as ohmmeters, voltmeters and oscilloscopes.
• Followed state and local building regulations based on National Electrical Code.
• Repaired Lighting in Hospital

* Ground Up Gas turbine facility

* Conduit Installations 1/2" to 4"

* Transformer terminations

* Perimeter cad weld grid grounds

• Connected wires to circuit breakers, transformers and other components.
• * Cable pulls

• Improved electrical system safety by conducting thorough inspections and identifying potential hazards.
• Enhanced energy efficiency by recommending and installing upgraded electrical components in residential and commercial properties.
• Troubleshot and repaired malfunctioning systems and components.
• Followed state and local building regulations based on National Electrical Code.
• Spliced, joined and connected wire to fixtures and other electrical components.
• Installed 120/208 volt systems and 347/600 volt systems.