Dalton Glover
Calera
Summary
Resourceful Technician known for high productivity and efficiently completing tasks. Skilled in troubleshooting, preventive maintenance, and equipment repair. Excel at time management, problem-solving, and communication, ensuring seamless operations and team coordination.
Overview
13
13
years of professional experience
Work History
Tech 2
MasTec
dallas, tx
03.2025 - 04.2026
- Inspected rigging for defects, documented findings, and coordinated replacements to maintain safety standards.
- Check all rigging if there's any bad take a picture, document it and send it in and replace it.
- Check document that tells you how much everything weighs and find the right slings and shackles to do job
- Mark out the drop zone with orange cone
- Stage everything out: dead mans, rotor stand and the rigging to tie it down.
Tech 2
Pearce Renewables
Stephenville, Texas
09.2022 - 05.2024
- Communicate with the Crane to bring down major components
- Move to the very top where we install the nacelle
- Communicate with the Crane to bring down major components
- Ensured crew inspected harnesses and tools each morning for safety compliance
- Replaced defective components or parts as needed.
- Replaced defective components or parts.
Lead Topout
Wood Duncan Craft
Duncan, South Carolina
01.2021 - 04.2021
- Check document tells you how much everything weighs and find the right slings and shackles to do job
- Mark out the drop zone with orange cone
- Stage everything out: dead mans, rotor stand and the rigging to tie it down.
- Start the day out greasing equipment and look over machines to make sure everything is to par
- Directed dump truck operations and utilized dozer and road grader for material application
- Checked over tools to ensure proper alignment for asphalt application. to make sure it's to grade and level
- Inspected rigging and tools to ensure safety and readiness
- Start the day out greasing equipment and look over machines to make sure everything is to par
- Applied water on construction site using a water truck to control dust. with a water truck
- Released crane and initiated blade installation process
Apprentice Plumber
Blackburn Plumbing
Durant, Oklahoma
02.2018 - 12.2019
- Performed various rough in tasks on construction sites
- Use an excavator and shovel to dig ditches and unload all material
- Measure out everything to make sure pipes are going to fall where they are supposed to
- Read blueprints, glue pipe and fittings together while maintaining elevation
- Use shovel and excavator to cover the ditches back up
- Assisted with top out responsibilities during plumbing installations
- Drilled holes for water lines and drains to ensure proper plumbing layout
- Installed stubs for water supply and drainage systems during plumbing installations
- Installed hot water heater and tankless hot water systems to enhance water heating efficiency
- Hook up sinks garbage disposals, dish washers, bathtubs and shower
Heavy Equipment Operator
Rk Hall
Denison, Texas
03.2018 - 11.2018
- Front end loader grease and fill up the equipment
- Load material in a hopper to mix with concrete
- Pushed material upward after it was dumped to ensure proper material flow.
- Logged and entered tickets into the computer system for accurate tracking.
- Remove excess material from loading pad to maintain safety and efficiency
- Cleaned surrounding areas of the plant and powered down equipment to maintain safety.
Combo Pipe Welder
G2 Construction
Monroe, Louisiana
02.2013 - 01.2015
- Read blueprints and see what kind of pipe we will be using in the paper mill
- Identified material type as stainless or carbon pipe for project requirements.
- Positioned pipe in stand, beveled edges with grinder, and cleaned surfaces with wire brush for optimal preparation
- Used two-hole level to ensure flange alignment for stainless steel connections.
- Executed root pass, fill pass, and cap pass during welding process.
- Welded pipe assemblies and operated JLG lift to transport completed sections to designated areas with permits
- Use lockout/tagout and ensure you have all permits
- Aligned and secured pipe, then performed welding to ensure strong connections.
- Conducted cleanup after welding, ensuring a fire watch remained for 30 minutes.
Education
High School Diploma -
Bennington High School
Bennington, OKSkills
- Rigging inspection
- Equipment operation
- Equipment maintenance
- Troubleshooting methods
- Problem resolution
- Safety documentation
- Project planning
- Work planning
- Time optimization
- Deadline management
- Leadership
- Teamwork
- Critical thinking
- Technical drawing interpretation
Timeline
Tech 2
MasTec
03.2025 - 04.2026
Tech 2
Pearce Renewables
09.2022 - 05.2024
Lead Topout
Wood Duncan Craft
01.2021 - 04.2021
Heavy Equipment Operator
Rk Hall
03.2018 - 11.2018
Apprentice Plumber
Blackburn Plumbing
02.2018 - 12.2019
Combo Pipe Welder
G2 Construction
02.2013 - 01.2015
High School Diploma -
Bennington High School