Enrique P Martinez

• Maintained quality assurance and customer satisfaction objectives.
• Executed diagnostics, troubleshooting and evaluations on Yokogawa system & dcs
• Organized work to meet demanding production goals.
• Completed job reports and logs immediately following service calls.
• Set up and performed test activities.
• Read manuals and manufacturer instructions to install and troubleshoot devices.
• Performed complex mechanical alignments and calibration of equipment to quality standards.
• Kept shop area and equipment clean, organized and maintained.
• Removed damaged instruments and repaired components.
• Identified issues by testing and troubleshooting instruments, components and assemblies using voltmeters, circuit testers and oscilloscopes. Follow lock out tag out procedures and permits
• termition of 4-20 analog wiring to instrument to junction box and to plc or dcs
• installation of temporary power for turn around planning
• demo out transformer and replace it back for generator steam turbine stg and wiring its junction box to the right landing point
• calibrate capillary transmitters and installation into high and low tap
• Demonstrated leadership skills in managing projects from concept to completion
• Participated in continuous improvement by generating suggestions, engaging in problem-solving activities to support teamwork.
• knowledge to use SAP program to gather information and new MOC work orders.
• Prioritized schedules to meet project goals and overall customer satisfaction.
• Recognized potential issues with inventory and quality control and engineered changes.
• Studied and interpreted equipment manuals, circuit diagrams, blueprints and schematics to determine corrective actions for repairs, calibrations and installations
• Self-motivated, with a strong sense of personal responsibility.
• Skilled at working independently and collaboratively in a team environment.

Pre loop instruments making sure is ready to shoot loop from instruments on the field to DCS or Triconex cabinets, making sure all wires are landed on the correct terminal block from Rie building to junction box to instruments on the field, using Trex heart to calibrate instruments, shooting loops simulate pressure or current 4-20 milliamps and use crystal and pump to send pressure value to Triconex sis system or C300. using 725 to drive temperature transmitters and make sure we have the correct type of wiring landed to read the correct temperature ambient reading. And use 789 to troubleshoot instrument and inspect for short on wire on field. QA/QC for mechanical instrumentation and electrical inspecting conduit and tubing making sure they are up to mechanical drawing and specs and correct wiring diagram. knowledge how to read p&ids and loop folders isometric drawing for piping.

• Cleaned and adjusted instruments.
• Inspected equipment to detect electrical leaks and other problems.
• Modified, maintained or repaired electronics equipment or systems to achieve proper functioning.
• Responded to problems with processing and production equipment and completed timely repairs.
• Demonstrated respect, friendliness and willingness to help wherever needed.
• Resolved problems, improved operations and provided exceptional service.
• Proved successful working within tight deadlines and fast-paced atmosphere.
• Participated in continuous improvement by generating suggestions, engaging in problem-solving activities to support teamwork.
• Identified issues by testing and troubleshooting instruments, components and assemblies using voltmeters, circuit testers and oscilloscopes
• Removed damaged instruments and repaired components
• knowledge to use SAP program to gather information and new MOC work orders.
• knowledge to read p&id isometric drawings mechanical installation and loop sheets and electrical schematics

• Studied and interpreted equipment manuals, circuit diagrams, blueprints and schematics to determine corrective actions for repairs, calibrations and installations.
• Liaised with engineering staff on special projects to assist with configuration, installation and interoperation of system equipment.
• Conducted preventive maintenance and troubleshooting of metering instruments.
• Performed scheduled and planned installation and maintenance duties.
• Trouble shooting thermocouples & making sure element is working up to ambient. driving temperature transmitters with 725. pulling new wire in conduit and terminating Knowledge Reading P&ID to locate instruments and flow direction on equipment. making sure all wires are landed on the correct terminal block from Rie building to junction box to instruments on the field, using Trex heart to calibrate instruments, shooting loops simulate pressure or current 4-20 milliamps and use crystal and pump to send pressure value to Triconex sis system. using 725 to drive temperature transmitters and make sure we have the correct type of wiring landed to read the correct ambient. And use 789 to troubleshoot instrument and inspect for short on wire. QA/QC for mechanical instrumentation and electrical inspecting conduit and tubing making sure they are up to mechanical drawing and specs and correct wiring diagram. knowledge how to read p&ids and loop folders isometric drawing for piping.
• Participated in continuous improvement by generating suggestions, engaging in problem-solving activities to support teamwork.
• Participated in team-building activities to enhance working relationships.
• Quickly learned new skills and applied them to daily tasks, improving efficiency and productivity.
• Performed duties in accordance with applicable standards, policies and regulatory guidelines to promote safe working environment.
• Used critical thinking to break down problems, evaluate solutions and make decisions.
• Run multiple racks of stainless steel 316 of tubing 1/8 1/4 3/8 1/2 3/4 1" and bundle insulated tubing and coper tubing for steam trace.
• install instrument air supply to supply air to control valves or other instrument devices
• termination of analog wires and high voltage

• Studied and interpreted equipment manuals, circuit diagrams, blueprints and schematics to determine corrective actions for repairs, calibrations and installations.
• Conducted preventive maintenance and troubleshooting of metering instruments.
• Performed scheduled and planned installation and maintenance duties.
• Operated multimeters, oscilloscopes, electronic testing devices to accurately diagnose equipment issues.
• Performed repair procedures on damaged instruments and sourced replacements from approved vendors.
• Liaised with engineering staff on special projects to assist with configuration, installation and interoperation of system equipment.
• Analyzed engineering designs and suggested improvements and modifications.
• Calibrated combustion controls to meet appropriate safety standards.
• Performed scheduled and planned installation and maintenance duties
• QC I&E mechanical material are up to specification
• Run multiple racks of stainless steel 316 of tubing 1/8 1/4 3/8 1/2 3/4 1" and bundle insulated tubing and coper tubing for steam trace.install instrument air supply to supply air to control valves or other instrument devices