Farrell Yazzie

• Running and installing 1 inch to 1 1/2 rigid pipes into Switch gears, power supplies and distribution units
• Ran and terminated wires
• continuity check on all wires
• Made sure pipe and wire went to there right location
• Installed disconnects
• Crimped and formed wires to there desired location .
• Notify all affected personnel of LOTO
• LOTO or tag each energy control point listed
• Utilize EEW suit/ hot suit
• Make sure using certified meter to check LDL live dead live. Zero voltage.
• Make sure equipment read zero voltage
• Double check PPE before LDL.
• Always be alert
• Know your surroundings/ location
• Making sure equipment reads zero voltage for inspectors or other workers that are LOTO at the equipment tested on
• Malign sure labels and wires are at there correct destination
• Making sure everything is ready for inspection

• Ran and installed conduits on all equipments
• Bend pipe to there desired length, angles and degrees
• Cut rigid pipe and re thread them
• Walked work area with crew ans identify hazards
• Discuss scope of work
• Review measurements and other information on computer.
• Made sure measurements that were on the schematic on the computer was correct
• Installed rigid pipe from commercial building to cooling towers.
• Terminated wires
• Labeled and made sure everything was ready for inspection
• Prefabricated supports for disconnects
• Locked out tagged out
• Terminated transformers and distribution panels
• Did alot of tool install
• Crimped wires
• Torqued bolts to recommend Torque specs
• Made sure all tools / power tools were in good working conditions
• Modify and install cable trays
• Given a computer so I can over look the tool install specs.
• Getting every thing ready for inspection

• Installed electrical units/ distribution panels
• Installed transformers
• Ran 750 wire into the distribution panels and terminated it as well. Made sure they were roped and secured to there desired location.
• Terminated the transformers
• Ran and Installed 2 to 4 inch conduit emt.
• Disassembled dead fronts on distribution panels and transformer panels
• Utilized EEW suit .
• Made sure meter was certified to check zero voltage or dead live
• Made sure my P.P.E was up to date for my performance on checking deadlive on all units
• Made sure my paper work was done before going into equipments
• Made sure equipment read zero voltage
• So other companions can work in them as well.
• Made sure every one locked out tagged out. "LOTO"
• Knowing the right procedures on locking out and tagging out
• Knowing the right procedures on using meter. Always check before use
• Having good buddy system
• Clean as you go
• Verifying breakers and good communication
• Barricade area. so others won't get shocked or hurt
• Had my crew. Made sure every one went to there right equipment.
• Made sure all P.T.P was signed
• 
  

• Installing electrical panels
• Terminating 120v, 280v and 277v
• Running wire and terminating wire. Wire sizes #12 to 750s
• Laying, installing and bending conduit 1/2, 3/4, 1 inch, 1 1/4 and 2 inch emt conduits
• Bending and installing rigid pipe
• Running power for refrigeration and units on top of equipment. As well as running data for all units.
• Powering up H-VAC units
• Installing 4ft to 8ft light fixtures
• Installing power poles for registers
• Labeling wires
• Reading plans and schematics
• Following safety rules

• Terminated 3 phase 480v panels
• Terminated motor controls
• Running, bending and installing 3/4 to 1 inch conduit
• Running and installing 2 1/2 and 3 inch conduit
• Installed deep and shallow struts
• Ran and installed rigid conduit as well
• Installed cable trays and ran cables
• Paid attention to instructions
• Followed jobsite rules
• Good communication with all employees
• Making sure job was a safe environment

• Wired invertors and terminated
• Wired invertors to the combiners. Terminated as well
• Terminated 3 phase 480v panels
• Terminated motor controls
• Ran cat 5e and optic fiber as well
• Installed cameras
• Installed and bend 3/4 to 1 inch conduit emt
• Installed deep and shallow strut
• Installed all threads and straps
• Installed beem clamps
• Ran rigid conduit
• Installed caple trays and Ran cables on them
• Made sure we were tied down to our harness all the time for safety purposes
• Listened and followed rules and paid attention to details

• Installed and ran alot of communication wire.
• Terminated phone jacks and receivers.
• Installed alot of trim for communications
• Installed alot of lighting throughout the jobsite
• Wired and terminated fluorescent lights
• Ran and bend 1/2, 3/4 and 1 inch conduit.
• Piped and glued together pvc conduit. All underground
• Terminated 3 phase 480v panels
• Terminated motor controls
• Ran and bend rigid conduit
• Installed cable trays
• Terminated transformers
• Followed instructions
• Made sure out work was competed and ready for inspection
• Making sure job is a safe environment

• Completed all course and safety classes for the mine
• Bend conduit, laid and installed pipe
• Ran wires and terminated all wires
• Installed deep and shallow strut
• Ran and installed rigid pipe
• Ran conduit 3 inch to 6 inches
• Installed cable trays
• Terminated 3 phase 480v panels
• Terminated motor controls
• Followed safety precautions
• Listened and followed rules and paid attention to instructions

• Wired residential and commercial units
• Ran #6, #8 and # 12 wire. 14/2 to 12/2 romex wire as well.
• Ran and installed phone and cable wire. Aka communications.
• Alot of upgrades on panels and sub panels.
• Terminated 3 phase 480v panels
• Terminated motor controls
• Set up service poles for mobile homes 190 amp to 200 amp panels.
• Ran and installed alot of pipe/ conduit. 1/2 inch to 3 inch conduit.
• Ran and installed rigid pipe
• Installed deep and shallow strut
• Installed been clamps with all thread and straps
• Installed cable trays
• Made sure everything we installed and wired was up to code
• Had responsibilities for our task. And had good communication with one another

• completely wired residential houses and custom homes.

• Installed rough in boxes for outlets and switches throughout the dwelling unit.

• ran romex wires throughout the dwelling units.

• Terminated all outlets and switches.

• installed panels and subpanels. Ran main powering to panels. Terminated all.

• Everything was installed and Wired up to code.

• Service calls as well.

• trouble shoot wires. Made sure everything worked before leaving the job

• Inspected electrical components for safety compliance prior to use.