Skilled electrician with proven experience and readiness for the role. Strong focus on electrical installations, maintenance, and repair, ensuring safety and compliance with codes. Excellent at collaborating within teams and adaptable to changing project needs. Known for reliability and delivering quality results.
Work History
Journeyman Electrician/ Data Center
3 Months
Mortenson | 07.2026 - Current
i do terminations in switch gears, panel board lugs , transformers, hmi cabinets
i do insulation resistance on all all cables which have been routed before I start terminating
Installed lighting and completed wiring terminations for light boxes and Moab boxes.
run cable tray inside msg for cable support going up the wall and going into the IC cabinet
Interpreted blueprints, schematics, and specifications to complete precise electrical rough-ins.
Executed MV transformer terminations for electrical connection work.
Journeyman Electrician/ Solar Farm
7 Months
T.I.C /Kiewit | 12.2025 - 07.2026
Executed CAT6 installation and termination between SCADA boxes and inverters, ensuring connectivity validated by cable certifier.
Terminated inverter DC and AC conduit runs using THHN and lugged connections to manufacturer torque specs.
Completed termination of inverter DC and AC conduit runs with THHN and lugged connections, adhering to manufacturer torque specifications.
Assembled and secured DC combiner boxes to rack supports, preventing cable strain and improving service access.
Coordinated conduit runs from inverter to combiner boxes utilizing 4 in Schedule 80 conduit, optimizing layout for effective cable management.
Journeyman Electrician /Solar Farm
1 Year 10 Months
Psc | 01.2024 - 11.2025
I would set cabinet sectionalizers, run underground DC/MV, Performed rough-in installations for inverters, ensuring proper placement and alignment. to set the inverters and do DC terms on combiner boxes plus on Inverters
Installed and aligned commercial inverters on concrete pads, securing mounts and grounding to meet NEC standards.
Executed DC disconnect installations and labeled circuits per wiring diagrams to simplify future maintenance tasks.
Completed 750 DC termination connections on combiner boxes, configuring wiring for efficient routing to inverter.
Electrical Apprentice/ Offshore Rig
10 Months
MMR | 01.2023 - 11.2023
Managed installation, monitoring, and troubleshooting of electrical systems onboard offshore rig, ensuring operational reliability.
Installed wiring, outlets, and fixtures under supervision, ensuring compliance with electrical codes and enhancing safety standards.
Tested electrical systems using multimeters, voltage testers, and continuity tools.
Executed termination of wiring for overhead lighting fixtures, emergency exit signs, and ceiling-mounted speaker phones according to installation requirements, contributing to overall functionality.
Read blueprints and schematics to support accurate layout, circuit identification, and material preparation.
Electrician apprentice/ Wind Farm
1 Year 10 Months
RES | 02.2021 - 12.2022
Excavated over 10,000 ft of trenches for MV cable runs between towers, facilitating safe cable routing and timely crew handoffs.
Installed ground rods and bonded grounding systems for turbines, ensuring compliance with NESC grounding requirements.
Conducted insulation-resistance and continuity tests on generator leads, accurately documenting results for commissioning log.
Installed wiring, conduits, and fixtures while following electrical codes and jobsite safety standards.
Assisted journeyman electricians with panel layouts, circuit terminations, and equipment hookups.
Side Boom/Trackhoe Operator
3 Years 2 Months
Pumpco inc. | 03.2017 - 05.2020
Excavated 6-ft deep, 1,500-ft trenches for 24" pipe, ensuring accurate grade and alignment for effective side-boom lowering.
Executed trench backfill using compaction attachments, adhering to inspector notes and meeting on-site compaction standards.
Operated pumping equipment and monitored gauges to maintain safe, consistent flow.
Inspected valves, hoses, and seals before startup to prevent equipment issues.
Adjusted pump controls and pressure settings to match job specifications.