Francisco Alba

Performed QA hold points on coating, fireproofing and insulation jobs for all soft craft contractors working in the new construction of the LNG project in Louisiana.

Assisted QA/QC meetings between the client, third party Inspectors and Contractor QCs.

Documented and reported quality surveillance reports.

Audited Soft Craft Contractor QCs Daily reports, Data Sheets, Certifications, Calibration of equipment, Inspection Test Plan, and QC final reports.

Performed final walkdowns on jobs and signed off job completion releases if all required specifications were met.

• Preformed Observations of items to be worked on
• Communicated with Client and Contractors to review job requirements for upcoming tasks
• Performed Pre Job walk downs
• Tracked and documented Contractor square footage, Percentages, Costs, Employees, Downtime, QC reports, Blast reports, Time, and daily progress using the Intellispect Software
• Performed Inspection hold points using various methods of inspection
• Performed inspections using rope access
• Documented all Data in Daily and Final Reports

• Communicated with contractor QC and Site Construction Rep
• To review the requierements and progress of ongoing and upcoming tasks
• Performed hold point inspections on thermal insulation installation on hot and cold service lines
• Performed final metal inspections on hot and cold service lines
• Documented and Tracked the progress of line completion on each module
• Signed off release forms and documented the completion of each module
• Witnessed Hydro milling and preservation on internal of piping

• Communicated with Client and QA to review job requirements for upcoming tasks
• Communicated with General Formans and Site Supervisors to ensure their knowledge and plan for the completion of job task
• Preformed a pre job inspection verifying that areas that meet a potential hazard of could be damaged are isolated, verified environmental conditions, and preformed a chloride and salt test (CSN Test) to ensure that the steel surface is free of contaminants
• After completion of surface preparation, the surface was inspected to meet the Nace standard required
• An anchor profile test was performed and environmental conditions were verified prior to coating application
• Verified coating to ensure expiration date, mixing procedures and ratios, volume solids and that mixer was using proper PPE
• Documented batch numbers for all parts and solvents used prior to application and environmental conditions
• After completion of coating application various tests were preformed such as dry film thickness, Solvent Rub Test, Pull test, Bend Test (TSA Application), High and Low Voltage Holiday Test to ensure the quality and requirements by the client were followed
• Documented all Data in Daily and Final Reports and Documentation was turned in to Client after completion of each job

• Completed tasks in a timely manner while meeting the safety and quality requirements in the repair of corroded surfaces and application of coatings on piping, structures, vessels, and tanks
• Performed Surface preparation on steel surfaces using methods such as hand tool, power tool, abrasive blasting, and blast tracking
• Performed methods of coating application using brush and roller, conventional and airless, as well as plural component pumps to meet the required dry film thickness after application
• Followed lead abatement procedures and safety regulations when performing tasks in lead contaminated environments by getting proper training and certifications provided by contractor
• Performed tasks on elevated surfaces while working off an aerial lift using proper certifications and training

• Completed tasks in a timely manner while meeting the safety and quality requirements in the repair of corroded surfaces and application of coatings on piping, structures, vessels, and tanks
• Performed Surface preparation on steel surfaces using methods such as hand tool, power tool, abrasive blasting, and blast tracking
• Performed methods of coating application using brush and roller, conventional and airless, as well as plural component pumps to meet the required dry film thickness after application
• Followed lead abatement procedures and safety regulations when performing tasks in lead contaminated environments by getting proper training and certifications provided by contractor
• Performed tasks on elevated surfaces while working off an aerial lift using proper certifications and training

• Participated in job site tool box meetings, safety meetings and wrote Job Safety Analysis documents prior to the beginning of job task
• Preformed surface preparation and coating application on maintance jobs using hand tools and power tools to prep surfaces and brush and roller to apply coatings
• Operated Blast equipment such as Blast Pots, Moister Traps/ Dryers, and compressors
• Operated Airless pumps and mixed Paint accordingly to meet mixing requirements by manufacturer