Summary
Overview
Work History
Education
Skills
Additional Information
Accomplishments
Certification
Timeline
Generic

Gina Eubank

Bothell,WA

Summary

Quality Assurance Inspector with 35 years of experience in manufacturing and quality control. Expertise in compliance with industry standards and timely delivery of certified aircraft. Proficient in conducting tests to identify production errors, enhancing product quality and efficiency. Strong analytical skills and problem-solving abilities contribute to continuous improvement initiatives.

Overview

37
37
years of professional experience
1
1
Certification

Work History

Quality Control Inspector

IDD Aerospace Avionics Division Safran Electronics
Redmond, WA
08.2016 - Current
  • Performed and ability to determine if work is completed precisely in accordance with instructions, engineering drawings, specifications, verify that approved special process sources are used (as applicable), and that the manufacturing planning/routing document calls out the correct specification, proven ability to perform inspection on behalf of customers.
  • Performed to inspect each part front face panel for testing lighting function properly and cosmetics defect, back panel for part marking correct, and follow IDD work instructions as Acceptance Test Procedure, Acceptance Test Report, FAI in net-inspect.
  • Ensures writing Non-Conformance process report and sending them to Supervisor Cart and MRB Cage for disposition.
  • Ensures shipping out going packages and double inspecting each package.
  • Performed inspect in each package by ensuring each a part matches up to the paperwork.
  • Ensure each part follows the spec, OP-WI-310 Rev.
  • B any cosmetics workmanship visual damage.
  • Performed using correct tools by measuring parts to a .03 tolerance level; using Kayence CMM machine, calipers, height gages, radius gages and diameter gages.
  • Ensures sending reports to the buyers and manufactures, after red tagging, writing a Non-Conformance Report and set the parts in the MRB cage for holding.
  • Performed to double check, all the previous stamps are legible and stamped, before stamping off and sending part to the next line.
  • Properly closing work orders then sending paperwork to Document Control and scanned all documents.

Quality Control Inspector

Spectralux Avionics Corp
Kirkland, WA
05.2019 - 07.2020
  • Over 28 years manufacturing production management experience as dedicated, results oriented electronics inspector / QC Technician / QC Receiving Inspector / Quality Control Inspector Interior Aircraft Interprets flow charts, engineering drawings, standards, and specifications to accomplish work assignments Strong computer skills; MS Office Suite (Word, Excel, Access, PowerPoint, Email Internet navigation research) Inspect of electrical, electronic, and mechanical systems to enable the performance of functional and operational tests.
  • Skill in the use of Kayence CMM machine, flat surface plates, calipers, radius gages, height gages.
  • Proven ability to perform inspection on behalf of customers Certified AS9100/IPC Specialist IPC-A-610D requirements for Class 2 assemblies, Performed all finished products shall be placed in Final inspection once all operations and corresponding documents have been completed.
  • Performed finished products from the Final Inspection rack to begin.
  • Ensures each color coded shelf has a different priority.
  • As followed are; first In and first out (Red: 1st priority must ship ASAP, Green: 2nd priority due date is soon, Yellow 3rd priority, White: Lowest priority.
  • Performed the Final Inspection.
  • Examined the routing document and any associated process documents.
  • Ensure the documents must filled out accurately and completely.
  • Verified the WO are completely filled out with the exception of the Final inspection and shipping lines.
  • (Initial and date “Final Inspection”).
  • Performed customer drawing in the routing packages, and find the document in controlled database and search by part number.
  • Ensures the drawing revision against the routing documents and part marking are correct.
  • Ensures that any test data is complete and in specification.
  • To ensures test/in process inspection data on the routing documents.
  • Performed mechanical measurements like (Micrometer Gauges, Bore Gauge, Calipers, Dial Indicator, Feeler Gauge, Gauge Blocks, Gauge Pins, Go/No-go Gauges, Radius Gauge) as needed and electronic measurements, brightness measurements, etc.
  • Ensures the required measurements are indicated on the work order and/or the ATR.
  • Verified dimensions/Tolerances can be found on ATR and/or on part drawings.
  • Performed the process documentation criteria as of part number, customer, color, revision level and part marking as required.
  • Ensures information against the part drawings.
  • Verified color chips and place the part and the corresponding color chip inside a light box to verify color.
  • Verified measure and / or verify characteristics.
  • Verified to make sure all screws are in panel and they are flush.
  • Ensure connectors for contamination, breakage, bent, bent pins, and to make sure all fasteners are in panel, check for cosmetics.
  • Checked to make sure circuit board is flush.
  • Verified all text on face panel matches drawing.
  • Verified part matches part number on work order.
  • To ensures all previous operations are signed and to make sure ATP operations are completed and properly signed off and make sure to verify ATP matches part number.
  • Ensures keyboards actuate each key per drawing requirements.
  • Reviewed work instructions for any additional requirements.
  • Quality Assurance Inspector Shipping Outgoing Products.
  • Performed to inspect the parts to build paperwork (traveler, ATR, other build/test paperwork) Verified part number, serial number, revision, color.
  • Ensures paperwork are complete and all sign off and verified QA stamps are on parts and legible.
  • Verified hardware installed on part (no missing captive screws, no missing flathead screws and they are flush.) Verified Manufacturing date (matches final assembly step sign off on traveler) Verified special C of C’s, FAI (blue traveler) when required.
  • Ensures parts to labels part number, serial number, revision, date code.
  • Verified parts to shipping pick list part number, serial number, revision, quantity.
  • Verified part marking check was signed off verify part number, verify revision, verify quantity, verify serial number, verify sales order, verify parts in the box match paperwork (P/N, S/N, SO, etc) Verified notes in ‘Special Instructions For Sales Order’ are reviewed for any additional/special requirements and they are included in shipping (8130-3s, ATP, FAI Special Certs, etc.).

Shipping and Receiving Quality Inspector

Aplus Products
Woodinville, WA
06.2016 - 08.2016
  • Performed to inspect in each package by ensuring each a part matches up to the paperwork.
  • Sending reports to the buyers and manufactures, after red tagging, writing a Non-Conformance Report and set the parts in the MRB cage for holding, date entry, compare parts to drawings.
  • Compare paperwork to each package that goes through shipping and receiving and compare price from paperwork to NAVison program.
  • Ensure all packages on the shelves are organized by oldest date code to the new date codes.
  • Performed proper lifting 30-50 + lbs.
  • Follow ISO regulations.

Quality Control Inspector

C&D Zodiac Aerospace Corp
Marysville, WA
03.2015 - 08.2016
  • Inspect in each package by ensuring each a part matches up to the paperwork.
  • Ensure each part follows the spec, BAC5578 and AS9100, and any visual damage, compare parts to 3D drawings, data entry.
  • Performed correct tools by measuring parts to a .03 tolerance level; calipers, height gages, and diameter gages.
  • Sending reports to the buyers and manufactures, after red tagging, writing a Non-Conformance Report and set the parts in the MRB cage for holding.
  • Performed all finished Edge Seal parts by making sure the part matches the spec.
  • Double check, all the previous stamps are legible and stamped, before stamping off and sending it to the next line, properly closing work orders then sending paperwork to document control.

Quality Source Inspector

Life Port, Inc. A Sikorsky Aerospace thru Verify Inc
Woodland, WA
06.2014 - 07.2014
  • Performed Inspectors in this position inspect raw stock, fabricated parts and sub-assemblies for conformance with applicable drawings, specifications, quality standards, manufacturing plans and for workmanship.
  • Fabrication Inspectors also perform various in-process inspections, audits and heat-treat inspections.
  • Receive, obtain or locate parts/assemblies and appropriate paperwork/online instruction per required procedures.
  • Verified part number, serial number and that the quantity matches paperwork or online system.
  • Verified all paperwork/online instruction (e.g., manufacturing order, applicable drawings, specifications, nonconformance items and any other necessary documents) is complete and accurate.
  • Performed the appropriate revisions of drawings, Engineering Changes, specifications and other documents are being used by the shop and inspection.
  • Performed tools used by the shop to fabricate parts have been approved by tooling inspection.
  • Reviewed the paperwork/online instruction, drawing and job.
  • Select and/or set up the appropriate measuring instruments.
  • Lay out parts/assemblies to establish reference points and check dimensions, as required Inspected dimensions and workmanship per the drawing, specification and plan.
  • Conformed visual weld inspection, as required.
  • Identified and document discrepancies and reject parts/assemblies.

Quality Control Inspector III, Quality Control Technician and Packaging

Applied Technical Services Corporation
Everett, WA
10.2006 - 03.2011
  • Performed extensive technical testing skills in Sierra Nevada Corporation production helpful and knowledge on scanners to determine functionality, free of defects, and properly labeled and ensure all units were free of cosmetic defects and contained the corresponding diagnostics, software, memory boards and numerous parts.
  • Monitor defects to engineer through use of a Defect Tag indicating the specified defect code.
  • Perform receiving inspection, Communicate results to area lead or Supervisor and support daily stand up quality meeting in assigned area.
  • Performed extensive technical testing skills in SNC production helpful and knowledge on scanners to determine functionality, free of defects, and properly labeled and ensure all units were free of cosmetic defects and contained the corresponding diagnostics, software, memory boards and numerous parts.
  • Monitor defects to engineer through use of a Defect Tag indicating the specified defect code.
  • Performed receiving inspection, Communicate results to area lead or Supervisor and support daily stand up quality meeting in assigned area.
  • Quality Coach will be responsible for compliance of processes and procedures in the Quality team.
  • Consider Coach on a daily, weekly and monthly basis for the purpose of Quality improvement.
  • Assist with special projects and other duties as assigned.
  • Support daily Quality meeting first in the morning and end of the shift in assigned area.
  • Performed First Article inspection for each process area.
  • Monitor all lines stops to ensure that corrective action was addressed and results are acceptable.

Surface Mount Production Line Lead / Quality Control Coach Inspector

ETMA Electronic Manufacturing Corporation
Redmond, WA
03.1989 - 11.2003

Assistant Leader

As Surface Mount Dept.
  • Oversaw work of 12 production line employees in manufacture of electronic computer, medical, and aerospace devices.
  • Familiar with use of calibrated tools used for inspection, measurement and verification, such as Inspect products using gauges, coordinate measuring machine, scales, calipers, micrometers, probes, height gages, oscilloscope, optical comparator and vision prior to shipment.
  • Ensure that all data entry into the Quality database is done for each work order.
  • (Standard work document Quality database data entry).
  • Performed reworked assemblies meet internal quality standards.
  • Complete quality control defect data sheets and other required documentation daily, and metrics with job performance goals and objectives.
  • Performed excellent component identification skills for SMT components part, including polarity, values and tolerances are required.
  • Inspect using a microscope, magnifying lamp or eye loupe for prolonged periods of time.

Education

Education Basic Computer; Certified AS9102 and IPC Specialist (IPC-A-610D) 2007; Certification Level 2-02 Practice Safe Practices for Oxygen Systems 2014 -

ApolinarioenceKayenceSpectraluxApolinarioenceKayenceSpectraluxApolinarioenceKayenceSpectraluxApolinario Mabini High School

Skills

  • Inspection procedures
  • Sampling protocols
  • Production experience
  • Quality control
  • Inspection documentation
  • Schematic understanding
  • Safety procedures
  • Reporting and documentation
  • Product testing
  • Supervision
  • Leadership
  • Communication

Additional Information

  • Basic English language skills and the ability to read, follow, and interpret planning and work order instructions Accurately reads and interprets engineering drawings, process specifications, and machine and/or tooling definitions. Verify part specific gauges and/or tooling is qualified and traceable, as applicable Skilled in the use of precision measuring tools for inspection, measurement gauges, measuring machine, scales, calipers, micrometers, probes, height gages, oscilloscope, optical comparator and vision prior to shipment. Superior and ability to determine if work is completed precisely in accordance with instructions, drawings, specifications.Verify that approved Special Process sources are used (as applicable), and that the manufacturing planning/routing document calls out the correct specification

Accomplishments

  • Promoted from electronic assembly line to Production Line Lead, in less than 12-months
  • Led team to achieve bonus reward, earning recognition from upper management and financial reward.
  • Drove 99.99% quality improvement in on time delivery profits through aggressive good quality and less error.

Certification

  • Specialized Training on Philips ( FCM, Emerald Sapphire Topaz, Topaz-AI and Fuji Machine, EKRA and DEK Screen Printer/ Certificates - 1992
  • Certified AS9102 and IPC Specialist (IPC-A-610D), Applied Technical Services Corporation - 2007 Certification Level 2-02 Practice Safe Practices For Oxygen Systems 2014

Timeline

Quality Control Inspector

Spectralux Avionics Corp
05.2019 - 07.2020

Quality Control Inspector

IDD Aerospace Avionics Division Safran Electronics
08.2016 - Current

Shipping and Receiving Quality Inspector

Aplus Products
06.2016 - 08.2016

Quality Control Inspector

C&D Zodiac Aerospace Corp
03.2015 - 08.2016

Quality Source Inspector

Life Port, Inc. A Sikorsky Aerospace thru Verify Inc
06.2014 - 07.2014

Quality Control Inspector III, Quality Control Technician and Packaging

Applied Technical Services Corporation
10.2006 - 03.2011

Surface Mount Production Line Lead / Quality Control Coach Inspector

ETMA Electronic Manufacturing Corporation
03.1989 - 11.2003

Assistant Leader

As Surface Mount Dept.

Education Basic Computer; Certified AS9102 and IPC Specialist (IPC-A-610D) 2007; Certification Level 2-02 Practice Safe Practices for Oxygen Systems 2014 -

ApolinarioenceKayenceSpectraluxApolinarioenceKayenceSpectraluxApolinarioenceKayenceSpectraluxApolinario Mabini High School

Similar Profiles

CREATE PROFILE