Heber Turcios

over the past 3 years I been a wireman panelist ans been responsible for following blueprint of each panel I have worked on. making sure every wire is up to standard and relays, breakers and terminal blocks are up to standard. Inspect completed panal for accuracy and quality. Use hand and power tools for more efficiently. Meet production deadline and following safety standards while keeping a clean work area also have experience in the control house.

• Troubleshooted systems and repaired equipment, ensuring compliance with all established guidelines.
• Installed safety and distribution components for electrical systems, such as switches, resistors and circuit-breaker panels.
• Installed 120/208 volt systems and 347/600 volt systems.
• Installed ground leads and connected power cables to equipment.
• Completed rough-in, termination, and underground work.

• Stored and maintained power tools and equipment for each job.
• Demonstrated expertise in use of cable reels, stripping tools, voltage detectors, and wire and cable cutters to complete fast-paced work.
• Repaired or replaced wiring, equipment and fixtures using hand tools and power tools.
• Installed, maintained, repaired, and tested equipment for electricity generation and utilization.

• Inspected trucks for malfunctions and reported vehicles to management for corrective action.
• Conducted efficient cargo transfers to maintain route schedules.
• Contacted dispatch to report delivery incidents and determine best methods for resolution.
• Demonstrated safe driving by following regulations and safety procedures, resulting in zero accidents.
• Kept accurate records of cargo delivery times and vehicle maintenance to provide documentation to dispatch for billing and inventory purposes.

• I was responsible for running conduits, running cable trades, pulling wires, doing Terminations.
• Installed 120/208 volt systems and 347/600 volt systems.
• Installed ground leads and connected power cables to equipment.

• I assisted electrician in basic tasks such as handling tools and completing maintenance work orders
• Measured and cut required supplies such as wire and conduit
• Gathered parts, supplies and tools in preparation for each workday or new job
• Do Terminations which are based on putting each wire where it belongs on the box and safety secured it
• Run Conduits which you have to measure and bend to place it where is required
• Check Snap tray, run it, cut it and screw it, Install lights, put supports.

• I was responsible for driving a Haul Truck, I had to move dirt from where we did not needed it to where we needed to cover the cement steps that had been done weeks before by other employees they all needed to be covered with dirt
• I had to use the Skid Steer alone or with forks to move dirk from side to side where it was needed
• Mini Excavator, I had to make holes move the dirt away or fill the haul truck with it also with the Loader I had to fill the haul truck to move bigger amounts of dirk
• Sheep's Foot
• Roller, I used this to compact the loose sand, there was steps and flat layers of cement that had to be cover with dirt and I had to compact it on all the flat areas that I could reach with the sheep foot roller.

• I had to move product pallets from the warehouse to loading area, complete orders and finding the product on each specific area the scanner says it is, if something is not where is supposed to be I had to find those pallets and put them back where they belong or sometimes there is pallets in front of the ones you need to complete an order.

• I was responsible for cleaning work area, supplying all tools and materials needed
• I had to run cable trays, conducts
• I had to install supports and pull wires, terminate junction boxes and run ground wire
• I had to keep supervisor inform of any materials required and progress of the work being done
• Before any work was done I had to send a request to get approved that there wasn't any type of gas or electricity on the area that the work needed to be done before getting into that area.

• In this company I was a Trench Roller Operator which was controlled by control remote and used on smaller areas where the road roller could not reach or was a small work for a big machine
• The Tele handler was used with fork pallets to move metal, wood or any hard to reach materials where it was hard to do it by hand or too heavy.

• In this project I was responsible for doing some minor torch ups doing either Stick or TIC
• I had to laid out fitted and fabricated metal components
• I was doing both welding types but both require different types of temperatures I was always careful because using the incorrect temperature means trouble.

• I was responsible for transporting, loading pallets of product from one place to other or from storage to where the trucks where loaded
• I had to scan and complete each order using a hand scanning device, sometimes items where not found where they should of been or where being other products so I had to move those to get the ones from my order and put those back where they was
• Forklifting is more about moving up and down loads and taking them from one place to other always with safety.

• From my previous job with TIC in Goldsboro, NC they knew I had experience has a welder so they transfers me to this project in Wilmington, NC where I was responsible for doing Stick structural welding which I had to do on corners, drafty areas and TIG which is more for pipes and different types of metals
• Everything had to be done by following the chart specifications and the type of welding that was requested.

• Being a scaffold builder is a lot of responsibility because others safety lays on it
• I had to build up and take down scaffolds wherever location it was needed, on low or high ground
• Scaffolds are made of different dimensions and sizes and I was responsible for making them and getting all the tools needed for it.