Jamarkus Harmon

• Working on 8.1 mods for C130 routing wire mods in aircraft, pinning, and crimping connectors.
• Troubleshooting wires, fixing broken wires on aircraft, and repinning broken pins into connectors.
• Reinstalling computers into the racks, and performing troubleshooting.
• On avionics systems.
• I also worked on CH-53 helicopters, completed wire routes, and performed.
• And reworked incomplete wire routes.
• Laercum C130 I routed harnesses in the aft sections of the tail, finished, and completed wire routes, reworked wire harnesses in the wire shop, and on a bench.
• Reading electrical wire diagrams and understanding faults.

• * Converting a Bell 214 helicopter into a firefighting aircraft.
• * Installing V2 tracing systems on Bell helicopters, modifying wires, studying schematics, and resolving faulty wire issues.
• * Troubleshooting Bell helicopter avionics instruments using pitot-static test equipment, conducting altimeter checks, vertical speed checks, and airspeed gauge checks.
• * Ensuring the absence of leaks in pitot-static systems.
• * Installing instrument panels and integrating oil pressure gauges, voltage gauges, master caution computers, and more.
• * Installing NAV GTN 750 computers.
• * Troubleshooting NAV computers and master caution computers.
• * Re-routing pitot-static hoses on the Bell 214 helicopter.
• * Implementing wire modifications and removing wires from eliminated systems.

• reworking mods that where done wrong fixing missed crimp pins into connectors broken wires completely ringing the aircraft from front to back
• reading wire diagrams interpreting mistaken wire routes incorrectly installed electrical hardware wires routed into incorrectly
• troubleshooting wires faults for wires that where not ringing correctly from point to point
• all work was done on coast guard aircraft

• Troubleshooting firex bottles on A220 aircraft
• Troubleshooting cabin lighting systems on A220
• Troubleshooting fly by wire and testing control surfaces on A220
• Troubleshooting pito probs
• installation of pito Probs
• Troubleshooting cockpit voice recorder
• Troubleshooting headset and microphones in cockpit verifying they work correctly
• Reading schematics and blue prints to identify faults in system
• Troubleshooting fuel systems making sure they read correctly
• Troubleshooting passenger lighting systems
• Installing and routing power feeder harnesses in engine pylon

• Removed installed up limit actuator on 560xl citation jet
• Pitio static troubleshooting on a Lear 60
• Performed Transponder troubleshooting and test check on a Lear 60
• Performed altimeter test check on a Lear 60
• Greased nose and main bearing on a G5 Gulfstream
• Performed emergency audio amplifier ops check
• Performed ELT ops check on a G4 Gulfstream
• Removed and installed temp sensor that was inop on a 560XL citation jet
• Troubleshoot inop landing gear light on a G4 Gulfstream
• Troubleshoot inop synch light on a 560xl citation jet and Removed and replace

• Cargo doors mods on a320,a319,a321,a330
• Wire deletions
• Troubleshooting pito static systems
• Installing epr & ispc cables
• Greased leading edge flap gears on routine maintenance check
• Remove and installed static wicks on trailing edge of ailerons elevators and rudder
• Serviced flap actuator & wire conduits under wing corrosion inhibitor
• Perform e wiz of fwd,cargo avionics and aft cargo compartment
• 
  

• Wire routing for ADSB mods on G550 Gulfstream jets
• Built modified and rework harnesses to new revisions on G550 GULFSTREAM JETS
• Built various harnesses coax antenna etc for G550 Gulfstream
• Performed crimping solder

• Installed wire mods for cargo door On crj's
• Installed glare shield mods for cargo door on crj
• Routed underfloor wire mods for cargo doors
• Above floor wire mods
• Supernumerary warning circuit termination
• Has done junction box mods for crj cargo doors
• Removed and installed computer racks
• Removed and installed all computer LRU,S
• Performed pito static testing on crj,s
• Generator feeder cables wire routing
• Cargo door smoke detector mods and wire routing for smoke detectors
• Has done emergency exit lights wire deletion on md-80,s , 737, crjs
• Ewis cleaning
• 
  

▪︎Performed ops check on static wicks using mega ohmmeter on crj 900

▪︎ removed panels from zone 100

▪︎ Installed raedoms on aircraft crj 900

▪︎ removed aft air supply ducks and mixer unit

▪︎ put double tention on elevator and rudder control cables in crj 900

▪︎ performed ewis cleaning of avionics bae and aft cargo bae

▪︎ ops check on cockpit lever thrust

reverse system

▪︎ performed manual operation of thrust

Reverse system

▪︎ installing bonding jumpers on left and right wing spoilers

▪︎ removed vertical fins on crj 900

▪︎ removed and installed dme & altimeter

Antennas

▪︎ removed sealant in the flaps area of the wings

▪︎ removed and installed insulation on crj 900

▪︎Readjusted landing gear ground proximity switches that where out off limits

▪︎Continuity test on main avionics power supply cannon plugs

Assisting military Apache helicopter mechanics with non routine maintenance removing and replacing ammunition racks

• Troubleshooted fire bottles on MD-11 cargo plains for left wing right wing and apu
• Installed fuel wire mods on the Md-11
• Temp sensor wire mod on the MD-11
• Perform ops check on CVR in cockpit
• Troubleshooted pitot static systems on MD-11 and 747 cargo plain
• Troubleshooted and perform ops check on underwater locater beacon on 747 under the radar nose dome
• Perform ops check and troubleshooted FADEC systems on MD-11
• Removed and replaced FMCs on MD-11 and IRUS
• Troubleshot and install antennas on 747s and MD-11
• Used IFR6000 to troubleshoot DME and Transponders
• Removed and reinstalled panels in 747 and MD-11s
• Routed GPS antenna wires for MD-11
• Installed battery packs for exit sign lighting on 747

Varifying and documenting work done. Labeling harnesses Routing wires, inserting wires into connectors, building connector assemblies,

Expected to work in a safe manner in accordance with established operating procedures and practices

• Building harnesses modified, rework, and reassemble harness assembles for companies such as Panasonic Boeing and Gogo.
• Ipc certified for crimping and soldering techniques
  Familiar with basic hand tools such as cutters (dykes) wire striper hand crimpers scissors soldering irons
• Reading and interpreting schematics Troubleshooting skills, familiar with testing equipment such as oscilloscopes, multimeters, frequency counters, etc.
• Fabricated Wire Harness in accordance to installation Manual,,, for various A/Cs such as Lithuania,
  Delta, Gulfstream, Panasonic & GoGo etc. also Formed Coax and quadrax cables - checked continuity - crimped
  and soldered.
• Job title was harness builder