Jorge Segura

● Live unit and new refinery.

● Walk down the facility with supervision into processing areas and walk down new construction areas.

● Fill out all permits and companies require paperwork prior to work.

● Analyze and study all blueprints for all work designed areas.

● Calculate all material to start work and future work.

● Plan work according to customer needs and redlines by the customer and engineering department.

● Install conduit support and cable tray ladder supports according to specs.

● Follow installation of conduit and cable tray runs according to blueprints, redlines and customer specs.

● Get approval of conduit and cable tray ladder by a quality control department before getting wire pulled in.

● Pull all power conductor wire into conduit and cable tray to all disconnects, lightning contactors, transformers, switch gears and motors.

● Pull all instrument and communication wires into conduit and cable trays to all boxes and instruments in the field.

● Terminate all power conductor wires after Meg cables for any rupture and insulation failure test.

● Terminate all instrument and communication cables into landing points according to customer or vendor schematics.

● Verify point to point landing points on every termination according to schematics, red lines and blueprints or vendor details.

● Install boxes, transformers, lightning contactors, stands, equipment and motors as customer specs and blueprints.

● Run all temporary power into the facility as a LOCK down power source of repairs and equipment removal.

● Perform demolition of conduit, boxes, cable tray or any electrical device as customer needs ot other contractor requests

● Live unit refinery

● Walk down facility with supervision into all processing areas and control rooms of operations.

● Fill out all permits and company requirements prior to work.

● Inspect all tools and equipment required for the task.

● Plan work according to blueprints and schematics.

● Install conduit supports and cable tray ladder supports according to specs.

● Follow installation of conduit and cable tray runs according to blueprints, redlines and customer specs.

● Get approval of conduit and cable tray ladder by a quality control department before getting wire pulled in.

● Pull all power conductor wire into conduit and cable tray to all disconnects, lightning contactors, transformers, switch gears and motors.

● Pull all instrumentation and communication wires into conduits and cable trays to all boxes and instruments in the field.

● Terminate all power conductor wires cables after Meg them out to verify any rupture or insulation failure.

● Terminate instrumentation boxes and instruments in the field according to customer specs.

● Verify point to point landing points and also make sure all side vendor cables are landed properly as vendor specs.

● Perform repairs as customer requests and needs.

● Communicate with Operations at the refinery or customer to energize any type of equipment or instrument.

● Turn around project

● Analize Blueprint and schematic prints reading.

● Accomplish production requested as customer needs.

● Keep track of material and customer orders to perform production deadlines as book requested.

● Operate all equipment with the authorization and certifications as customer required.

● Inspect all fall arrest systems to work at elevated areas.

● Conduit demolition to reactor area for pre Tar removal.

● LOTO procedures to disconnect circuits and demo existing cables and boxes.

● Install new lightning panels for new routing of circuits.

● Install conduit and supports for ne routing of Rigid conduit

● Pull wire to all receptacles and lightning.

● Meg all cables after wire pulling.

● Terminate all receptacles and lights with their designed TAGs.

● Get with operations to Turn on lightning panels after verifying LOTO.

● Temporary power across the unit for other contractors.

● Follow a routine maintenance checklist.

● Transfer tools, parts, equipment and supplies to and from workstations.

● Connect and disconnect wiring, piping and tubing.

● Refer to blueprints, repair manuals and parts catalogs to diagnose and repair equipment.

● Maintain and repaired tools, equipment and machines.

● Lubricate shafts, bearings and machinery gears.

● Operate precision measuring instruments and electrical and electronic testing devices.

● Inspected drives, motors and belts.

● Operate hand tools to adjust functional parts of devices and control instruments.

● Serviced systems for air handling, hydraulic, electrical, valves, circuits and pumps.

● Transfer tools, parts, equipment and supplies to and from workstations.

● Connect and disconnected wiring, piping and tubing

● Refer to blueprints, repair manuals and parts catalogs to diagnose and repair equipment.

● Maintain and repaired tools, equipment and machines.

● Lubricate shafts, bearings and machinery gears.

● Operate precision measuring instruments and electrical and electronic testing devices.

● Frequently diagnose mechanical problems and determine how to correct them.

● Service systems for air handling, hydraulic, electrical, valves, circuits and pumps.