Josh Stelma

• Performed physical activities requiring heavy lifting, walking and standing for long periods of time.
• Completed variety of physical labor tasks.
• Lifted objects weighing up to 50 pounds without assistance when necessary.

Handled all the wall finished exterior and interior

All the work from floor to ceiling demo and renovations , carpet, frp, acoustic ceilings, ect.

• Repaired damaged doors by replacing hinges, locksets or frames when necessary.
• Painted interior rooms with desired colors according to customer specifications.
• Installed plumbing fixtures, including sinks, toilets, bathtubs and showers.
• Installed cabinets, countertops, appliances and other fixtures in kitchens and bathrooms.
• Performed minor repairs, such as replacing light bulbs, patching walls and repairing door hinges.
• Patched holes in ceilings and walls using spackling paste or joint compound.
• Tightened loose screws on railings, handles, hinges to restore structural integrity.
• Measured and cut drywall for installation of new walls or repair of existing walls.
• Applied sealants around windowsills to prevent water infiltration.
• Assembled furniture from flat packs.
• Caulked cracks between baseboards and trim moldings to prevent dust accumulation.
• Cleaned gutters to ensure proper drainage away from the building's foundation.
• Maintained maintenance schedules and completed timely repairs.
• Constructed decks or patios to create additional living spaces outdoors.
• Installed tile backsplashes in kitchens and bathrooms to improve aesthetics.
• Maintained outdoor areas by mowing lawns, trimming hedges and removing debris.
• Replaced faulty wiring in electrical circuits and outlets.
• Repaired or replaced broken windows and window locks.
• Kept equipment in good working order and facilities clean, neat and organized.
• Installed shelving units for storage purposes.
• Inspected roofs for signs of damage or wear-and-tear; repaired any identified issues.
• Pressurized washed exterior surfaces of buildings to remove dirt and mold build up.
• Provided general maintenance services such as oil changes and tire rotations on vehicles.
• Operated hand tools and power tools to make minor maintenance repairs and maintain grounds and walks.
• Replaced wall sockets, ran lines and completed basic carpentry to finish installations.
• Identified problems during daily work inspections and addressed concerns.
• Cleaned vents and replaced filters to verify proper air flow.
• Repaired minor carpentry, electrical and plumbing issues to return equipment to functionality.
• Maintained clear and safe workspace areas to meet OSHA standards.
• Diagnosed equipment malfunctions and performed repairs to restore equipment and maintain uptime.
• Changed air conditioning filters to improve indoor air quality and help HVAC system perform properly.
• Removed snow from sidewalks, driveways and parking areas.
• Performed tasks to maintain on-site physical security, safety and efficiency.
• Followed correct procedures for handling, transporting and disposing of new and recycled materials.
• Repaired equipment and machinery, performing maintenance according to updated industry standards.
• Maintained compliance with internal and regulatory safety standards.
• Calculated required materials needed based on field measurements or work orders.
• Assisted with installing and maintaining electrical and power systems during remodeling projects.
• Collaborated with team members to assess equipment performance needs.
• Used rulers and micrometers to inspect parts and determine dimension requirements.
• Diagnosed and repaired mechanical issues according to industry standards.
• Repaired machines, equipment or structures using tools or equipment.
• Ordered parts, supplies or equipment from catalogs or suppliers.
• Implemented preventive maintenance practices and upheld equipment guidelines to avoid failures.
• Set up and operated machine tools to repair or fabricate jigs, fixtures or tools.
• Recorded type and cost of maintenance or repair work.
• Adjusted devices or control instruments using hand tools, levels or straightedges.
• Dismantled machines, equipment, or devices to access and remove defective parts.
• Planned and laid out repair work using diagrams, drawings or schematic diagrams.
• Diagnosed and corrected mechanical problems using blueprints, repair manuals or parts catalogs.
• Implemented troubleshooting techniques to resolve issue.
• Routinely inspected equipment for preventive and emergency maintenance needs.
• Cleaned or lubricated shafts, bearings or other parts of machinery.
• Installed equipment to improve energy or operational efficiency of residential or commercial buildings.
• Aligned and balanced new equipment after installation.
• Performed routine maintenance by inspecting drives, motors or belts.
• Applied paint with brushes, rollers, spray guns, or other equipment.
• Cleaned up job sites after completion of projects.
• Used power and hand tools safely and effectively.
• Used ladders and scaffolds to reach high walls and ceilings.
• Painted walls and other surfaces using traditional and sprayer methods and worked efficiently to complete jobs within required timeframes.
• Cleaned and smoothed surfaces prior to painting.
• Prepared surfaces by washing, scraping, sanding, and patching holes.
• Cleaned and properly stored paint equipment and supplies at end of each workday.
• Wore protective clothing such as masks, respirators and gloves.
• Primed, smoothed and cleaned trim, walls and ceilings to prepare for painting tasks.
• Performed repairs to defects in walls by patching holes and scrapes prior at project start.
• Readied surfaces and surrounding areas for painting with sandpaper, tape and other materials.
• Applied primers and sealers to prepare new surfaces for painting.
• Performed minor repairs, such as caulking windowsills, before painting them.
• Inspected painted surfaces for defects such as cracking, blistering, or fading.
• Sanded woodwork prior to staining or painting.
• Sprayed prepared surfaces with specified amounts of primers and finish coatings.
• Assessed work areas to determine safety measures required before beginning the job.
• Consulted with clients regarding colors and finishes.
• Repaired cracks in drywall prior to painting or wallpapering rooms.
• Applied paints, sealers and solvents to plaster, sheetrock, concrete and wood.
• Smoothed and finished surfaces on walls, trim and cabinetry.
• Protected furniture from dust generated during the preparation of walls.
• Mixed and applied paints, varnishes and sealants to promote lasting finish.
• Prepared sheetrock, metal and wood surfaces for painting.
• Spread undercoats and finish materials using rollers and spray equipment.
• Operated airless spray equipment and motorized lifts.
• Identified surface to be covered and characteristics of finish to properly select roller, power sprayer and right size brush.
• Performed minor plaster repair, blending newly renovated wall surfaces with existing plaster.
• Removed old wall coverings before applying new ones.
• Chose correct brushes and materials for jobs and purchased from vendors.
• Selected appropriate paint colors based on customer preferences.
• Mixed paints to desired color and texture.
• Estimated cost of materials needed for the project.
• Performed series of surface preparation techniques to maximize paint durability.
• Maintained thorough inventory of paint equipment and supplies by checking product levels.
• Selected, mixed and applied surface coatings to match and restore interior or exterior surfaces.
• Inspected work sites to measure dimensions, lay out work and estimate materials for each job.
• Followed the manufacturer's instructions when mixing chemicals for special applications.
• Mixed paints and solutions and monitored consistencies.
• Provided expert advice on the best products to use for various jobs.
• Ensured proper ventilation while using solvents or oil-based paints.
• Documented progress and provided estimated completion time for clients.
• Measured, cut, and installed wallpaper.
• Recommended blending, harmonizing and contrasting color options to customers.
• Covered floors before prepping, priming and painting walls and ceilings to protect them from chemicals and paint.
• Filled cracks, holes or joints using caulking guns or putty knives.
• Smoothed surfaces using sandpaper, scrapers or sanding machines.
• Removed old finishes by stripping, sanding or using water or abrasive blasting.
• Applied primers or sealers to prepare bare wood or metal for finish coats.
• Removed pictures, door knobs or electric switch covers prior to painting.
• Completed high-volume weekly painting jobs with consistently positive customer feedback.
• Mixed and matched paint, stain or varnish with oil or thinning and drying additives to obtain desired colors and consistencies.
• Completed diverse repairs on commercial and residential buildings and equipment.
• Washed and treated surfaces with oil, turpentine or other preparations.
• Constructed scaffolding and supports to complete work above ground-level.
• Selected and purchased tools or finishes for surfaces to be covered.
• Monitored paint supplies, placing orders whenever needed and properly and safely disposed of old paint.
• Calculated amounts of materials and estimated cost based on surface measurements or work orders.
• Erected scaffolding or swing gates or set up ladders to work above ground level.
• Used various carpenter's hand tools, portable power tools and standard measuring instruments.
• Performed various carpentry duties, including both rough and finish carpentry.
• Operated power tools safely when performing carpentry tasks such as drilling holes into lumber pieces.
• Installed drywall sheets onto walls or ceilings using nails or screws.
• Measured, cut and shaped wood materials to specifications using hand tools, such as saws and chisels.
• Maintained a clean job site at all times by disposing of debris properly after each shift.
• Shaped or cut materials to proper measurements using hand tools, machines or power saws.
• Installed interior trim work such as baseboards and moldings around windows and doors.
• Cut timber, panels and other wooden materials according to measured dimensions.
• Repaired or replaced damaged or defective parts using power tools and equipment.
• Repaired or replaced damaged structures or components.
• Promoted team safety by keeping work areas free of hazards.
• Used band, circular and compound miter saws.
• Installed cabinets, base cabinets and crown molding.
• Fabricated staircases, doors, window frames and other wooden components for buildings.
• Fitted door locksets, deadbolts and other hardware on doors according to manufacturer's instructions.
• Positioned and installed floor joists, trusses and rafters.
• Read blueprints, schematics and drawings to determine layout requirements.
• Installed building windows, trim and cabinetry alone or with assistants to meet job deadlines.
• Conducted inspections, diagnosed problems, took measurements and made necessary adjustments to complete projects according to specifications.
• Studied blueprints, sketches or building plans to prepare project layout and determine dimensions and materials required.
• Performed routine maintenance on carpentry equipment such as saws and drills.
• Constructed forms for concrete pours in accordance with building codes.
• Installed cabinets, fixtures and trim according to plans and blueprints.
• Cut and installed tile and hardwood flooring for residential and commercial buildings.
• Led apprentices and trainees in building construction and renovation.
• Prioritized work, keeping carpentry jobs on task and within budget.
• Assembled furniture using glue, dowels, screws and nails.
• Built jigs and fixtures to assist in the production of parts.
• Reviewed jobsite needs with foreman and coordinated construction.
• Laid out flooring patterns according to design templates or customer specifications.
• Prepared surfaces by sanding or scraping off old finishes prior to refinishing them.
• Examined buildings and project specifications to determine measurements.
• Assisted in the installation of metal framing systems for commercial construction projects.
• Measured, cut, and installed staircase spindles.
• Hand-assembled needed parts with bolts and screws.
• Verified dimensions of parts with calipers, micrometers, rulers and other precision measuring instruments.
• Polished furniture pieces with buffing wheels to achieve a high gloss finish.
• Assembled components using hand tools and power tools in accordance with blueprints or drawings.
• Installed hardware such as hinges, locks, catches and fasteners onto furniture pieces according to instructions.
• Maintained records of production data including material usage rates, quantities produced and quality control results.
• Maintained accurate records of production activities.
• Troubleshot problems related to equipment malfunctions during the finishing process.
• Reviewed all reports available to control costs, schedule work and eliminate shortages.
• Assisted with setup operations by positioning parts into fixtures or jigs for machining operations.
• Sanded down rough edges of woodwork items to create a smooth finish.
• Developed templates from drawings or plans for use in cutting out shapes from materials such as plastic laminates.
• Selected appropriate materials based on customer specifications and budget constraints.
• Monitored employees by inspecting work for accuracy, quality and throughput.
• Troubleshot equipment issues and determined best courses of action for repairs.
• Ensured compliance with environmental regulations when disposing of hazardous waste materials from finishing processes.
• Operated machinery such as drill presses, routers, grinders and saws to perform finishing tasks.
• Stored finished products securely until delivery is scheduled.
• Followed safety protocols when working with hazardous chemicals used in the finishing process.
• Provided accurate timelines for project completion to key stakeholders.
• Repaired damaged wood surfaces through filling cracks, holes or gouges with putty or wood filler.
• Performed sanding and grinding on metal surfaces to ensure smoothness of the finished product.
• Applied protective coatings such as lacquers, stains, sealants and varnishes to enhance the appearance of the finished product.
• Cleaned, prepared and painted metal components using a variety of techniques including air-brushing and spray painting.
• Inspected products for defects in workmanship or materials prior to completion.
• Used numerous types of power tools and other equipment daily.
• Verified trueness of construction using plumb and level.
• Anchored and braced forms and other structures in place using nails, bolts, anchor rods, steel cables, planks, wedges and timbers.
• Fashioned frameworks or props using hand tools and wood screws, nails or glue.
• Erected scaffolding to assemble above-ground structures.
• Studied blueprints or building plans to prepare layout and materials required.
• Consistently constructed square and level projects.
• Roughed in door and window frames or subflooring in structures undergoing construction or repair.
• Measured and marked cut lines on materials using ruler or marking gauge.
• Removed damaged or defective parts or sections of structures and repaired or replaced using hand tools.
• Took accurate measurements to calculate size and amount of materials needed for project completion.
• Communicated with teammates and supervisors frequently to understand requirements and complete projects on time.
• Installed windows, flooring, or trim using hand or power tools.
• Worked independently on projects and tasks within carpentry team.
• Utilized various tools, equipment, materials and forming systems to complete construction tasks.
• Maintained clean and organized workplace to optimize performance, efficiency and safety.
• Cut countertops from laminated material following template measurements.
• Laid and stained oak casings and hardwood floors.
• Procured and completed required permit approvals prior to starting projects.
• Anchored and braced forms to complete precise joining.
• Applied design-specific wood and composite trim according to architectural plans and neighborhood regulations.
• Applied acoustic paneling to ceilings and walls to adjust sound absorption and rebound within rooms.
• Provided consultation services for homeowners regarding custom carpentry designs.
• Inspected completed projects for quality assurance purposes before delivering them to customers.
• Contracted and collaborated with specialty sub-contractors for special trade jobs or installations.
• Calculated material costs for projects based on labor estimates provided by clients.

Various jobs and tasks around the concrete plant.

• Inspected finished products for conformance to quality standards.
• Loaded raw materials into the hopper feeder system of the corrugator machine.
• Followed established work instructions for each job assignment.

Performed all tasks pertaining to the corrugating and backing of cardboard

• Set up, adjusted, and maintained corrugator machine according to specifications.
• Troubleshot problems with the machine and made necessary repairs or adjustments.
• Maintained cleanliness of work area by removing scrap paper from machines.
• Ensured that all safety procedures were followed when operating the corrugator machine.
• Adjusted rollers and blades to ensure proper alignment of material.
• Identified opportunities for improvement in efficiency and productivity within the department.
• Assisted other team members in completing tasks related to production.
• Performed routine checks on equipment to ensure it was functioning properly.
• Measured materials accurately prior to cutting them on the corrugator machine.