Ruben Gomez

As a B.O.P.E tester my job was to show up to shop with helper and perform unit inspection,load out list,load p.p.e, tool list,and trouble shoot unit for leaks and needed lubricants. Leave shop show up on Oil Rig sites with all proper paper work and J.S.A , give safety meetings meet with Comp. Representatives and supervisors perform Hydro testing on Blow.Off.Preventer. Stack and valves from 0-15k psi. after area was clear from all personal. chart and record test report to management for further analysis.

As a Roustabout my job was to perform daily tasks and maintenance on customer lease fixing oil and gas lines. I was assigned to a crane operator and welder as a helper job including pipe cutting, removal and installation bolt up, grease, and test. valve replacement,tank installation,road crossings,and oil cleanups.

With T.i.c my job was to perform day to day tasks including gasket changes,greasing and oiling vales and pumping units routine maintenance and cleanups. with a good attitude, within time frame and group of people.

Perform day to day tasks including cutting,beveling,threading pipe and valve installation for the oil and gas industry. Pipe Install according to engineering specs. In different settings and systems from steam generators,pumps, and piping systems routing to co-gens

Performing tasks including. Field routing,measurments, and field verification cutting,beveling,threading and grooving. According to blueprints. building,installation,hydrotesting and final turnover to the client. Use of carry deck,crane,and fork lifts to install piping,valves and pipe instuments.

my job duties were to oversee, cut, and fab from 4"-24" HDPE pipe, 4 sections 800 ft. in length totaling 3200 ft. plus or minus depending on the tie ins the job included using a hand held tablet called a data logger witch logged the pipe size, weight, type, and DR type then start to finish when in fusion mode witch would in the end would determine if the weld was good or bad.

As a Pipe Foreman in Cortez hills gold mine, my duty was to manage a pipe crew consisting of 13 people in various areas of the mine carrying out different tasks from redline pipeing layout supports and routing gas,air,water, and sump lines from 4" to 12" CS pipe that fell within the time deadlines according to client scheadule.

Along with running a crew it came with scheaduling 1 to 6 week work scheadules and approval for time and tools and material needed to accomplish the job

As a Hdpe pipe fuser technician my job was to layout,field verify, cut,fab and install piping systems using various of fittings from 2" to 12" dr11, dr17 using track star 412 to 618 as well as 2" to 6" pit bulls. the work performed is up to management and client standards with precision spool drawings/iso and all recorded with a hadheld data logger.

As a mechanical craftman the job consisted of walking out p&id and iso configurations of boiler,heat exchangers,and piping installations marking and tagging for isolation points and demo work and installing of new equipment and pipe according to blueprints provided by the client and engineers, my posistion included repairs cutting threading fitting removal and installing of these systems

• Read and interpreted specifications, diagrams and blueprints for job.
• Handled all responsibilities for piping systems, including fabricating, assembling, installing and maintaining.
• Fabricated and positioned screw pipe, socket weld pipe and stainless steel tubing.
• Threaded pipes using specified machinery.
• Performed hydrostatic pressure testing of boilers and pressure vessels.

Read and understand, perform, build, and install, and hydro test pipe according to blueprints and ISO's spool sheets. Day-to-day tasks, including job layout, measurements, and building spools according to final measurements. Performing cutting, beveling, threading, grooving, fusing, socket weld, according to engineering blueprint specs.

• As a pipefitter my duty was to read understand and build to iso spool drawings
• Field verify take measurements using various hand tools incl. Levels,plumb bobs,5 points laser levels
• Cut prep fit and install piping systems incl. Stainless and carbon piping
• Install and bolt up pipe and help out technicians istall tubing drill support sand paint

• Performed issued tickets according to specific systems and or parts of engines including installation and removal of test rockets.
• Solved maintenance problems by assessing information from engine blueprints, drawings and other schematics.
• Identified issues with malfunctioning rocket engines and initiated appropriate repair work.
• Used, handled, stored and disposed of hazardous materials according to environmental standards.
• Performed inspections, maintenance, testing and repair work on engines and other aerospace propulsion systems.
• Used hazardous materials in compliance with Cal OSha regulations and verified proper disposal.
• Updated maintenance and repair logs according to services performed and submitted reports to supervisors for review.
• Measure,cut,prep,bend,fit, field verify and istall various tubing and piping of different types of wall thickness and Stainless steel materials.
• Installation of valves,vents,gauges
• use of various welding techniques due to the type of job being performed.
• (TIG) tungsten inert gas, for piping using argon and purging
• (SMAW) shield metal arc welding for structural supports
• (MIG) metal Inert gas for small and time sensitive welds

• Read and interpreted specifications, diagrams and blueprints for job.
• Handled all responsibilities for piping systems, including fabricating, assembling, installing and maintaining.
• Threaded pipes using specified machinery.
• Fabricated and positioned screw pipe, socket weld pipe and stainless steel tubing.
• Build, hydro test, and commission PVC,CPVC,HDPE piping systems.
• Work with engineer's on Isometric drawings and PNID. building and fabricating structures to support piping systems.
• Mig, Tig weld CS supports and sch 40. Piping

• Supervised a team of pipefitters to ensure safety protocols were adhered to, schedule, write daily, and weekly reports.
• Ensured all piping systems met industry standards and codes for quality assurance.
• Job planning with commissioning on various piping systems in Refinery units, hydrostatic and pneumatic blowdowns.
• Turn over P&ID and completion paperwork to the client, ensuring proper protocols and procedures were followed, and turn over specific systems ready to be tested.