Kelsey Brooks

• Certified Crane Signaler
• Certified Crane Rigging
• Certified Forklift Operator
• Certified Manlift Operator
• Certified Scissor Lift Operator
• Trained & Certified OSHA 10 & 30
• Trained In Infectious Control Risk Assessment
• Trained In Fall Protection
• Led team in framing, drywall installation, and finish carpentry projects, ensuring compliance with safety protocols.
• Supervised daily operations, coordinating schedules and resource allocation for project efficiency.
• Trained apprentices on carpentry techniques, enhancing skill development and workforce competency.
• Collaborated with project managers to assess project requirements and deliver solutions on time.
• Conducted site inspections to ensure adherence to building codes and regulations throughout construction phases.
• Provided a safe work environment for everyone on site made sure to communicate with everyone.
• Ran equipment Forklift , Scissor Lift, ManLift,

• Use a skid steer to mill out old black top and use various machines and hand tools to bring the work area up to specific ground grading to make sure the proper measurements where met, to insure when new black top was applied the work area was ready for proper work to be performed.
• Measure and mark cutting lines on materials, using a ruler, pencil, chalk, and marking gauge.
• Install structures or fixtures, such as windows, frames, floorings, trim, or hardware, using carpenters' hand or power tools.
• Remove damaged or defective parts or sections of structures and repair or replace, using hand tools.
• Construct forms or chutes for pouring concrete.
• Work with or remove hazardous material.
• Perform minor plumbing, welding, or concrete mixing work.
• Read blue prints for various job sites that where calling for different concrete panels and forms.
• Used various paving machines to pave different highway roads, Drive ways and various private roads.

Hung & Finished Drywall Level 5 Finisher

Framing Walls

Tie Rebar

Hung Ceiling Gride

Operated Heavy Equipment Forklift, Man Lift, Scissor Lift, Skid Steer, Excavator.

Paint Interior & Exterior

Read Blueprints

• Performed various work skills such as Framing, Roofing, Painting, Reading blue prints for new housing construction.
• Maintained safety as well as made sure other co-workers were also performing proper work duty's and following all safety procedures.
• Installed new structures, updated systems and replaced worn components to bring buildings up to current codes.
• Loaded and unloaded building materials used for construction.
• Determined materials needed for daily shift and loaded vehicles with equipment and supplies.
• Gathered waste and trash from job sites for placement in re-usable containers to keep job sites cleaned and organized.
• Brought materials and tools from trucks and storage facilities to work site locations and organized for expected needs.
• Gathered and disposed of work site debris to remove safety hazards and insure safety for other employees on the job site.

• Safety trained and Qualified for OSHA and MSHA job sites.
• Safety trained and Certified forklift driver, JLG lifts, Scissor lifts, and Skid steers.
• Safety trained and Certified Welder in Arc stick welding, Mig-welding and Flux core welding, Training involved performing G4,and G2 welding test that included Over-head, vertical, horizontal, and flat welding.
• Safety trained and Qualified to motion and signal over-head crane operators to perform various job duties. Such as loading and unloading semi-trucks with building material needed for various jobs. Signaled Crane operators to place structural beams where they where needed following specifications of job Blue-prints that where viewed and job briefed over before a job project began.
• Used various hand tools such as Oxygen and Acetylene torch, Grinders, Band saws, Air impacts, Etc.
• Followed standards and procedures to maintain a safe and productive work environment for myself as well as other co-workers and supervisors.
• Completed tear-downs of existing structures and prepared for new construction. Various job sites include Bridges and Road ways, Cement and Coal plants, Automotive production Factories and Shipping facilities.

• Safety trained and Qualified in injection molding machine operating and mold technician.
• Safety trained and Qualified for forklift driver and small crane lift.
• Observed operations of automatic molding machinery to detect and correct jams or malfunctions.
• Studied manuals and conditions to accurately determine prescribed temperature and time setting for each material and mold.
• Worked with Quality control, Plant Manager, and Supervisors to resolve production problems, improve operations and provide expected quality for the companies that where buying the products our company manufactured.
• Work duties performed was to start up machines and prepare them for production. Read and adjust machines to the proper settings the product was rated for. Adjust the machine to fix production rejections if the machine starts to malfunction at any time during production.
• Other work duties included to install and reinstall injection Molds into various machines when the production order was completed and ready for a new order to begin.