Lara Bui

• Certified in LN2
• Certified in Temlink
• Certified in Exsolve

-Maintaining tool APM schedules to run 4 & 8 day cycles

-Running jobs in auto mode through Fouploader and manual mode through Devkit program

-Proficient in navigating olaf system to prioritize jobs via dispatch order

-Understanding the importance of siteproc and assigning jobs in accordance to tool capability/health

-Promoting jobs once complete and moving to the next area of lab workflow

-Using FEI viewer to verify jobs have completed and to review images for recovery

-Recovering failed sites and processing jobs to completion

-Using pattern match editor to retrain failed sites in landing accuracies

-Understanding when to reset a block status in recovery

-Using sem beam to navigate specific sites for verification purposes

-Understanding the differences in Sem Beam view, Fib beam view, and Optical view when operating the XTmicroscope

-Applying discernment in making a judgement on what tools may need or what jobs must run in order to most wisely manage time

-Maintaining crucial communication with other team members and tool owners/engineers

• Routine ppe procedures followed per location of designated job
• Peer trainer for all new hires
• Safety representative(attendance to monthly meetings)
• Installation of upgrades and modifications on existing systems according to predefined specifications
• Perform troubleshooting, repair and maintenance of vacuum pump systems on customer site
• Removal and reinstallation of heat trace; installment of thermal jackets to pump systems
• Exhaust breaks, removals and reinstallation
• Maintaining crucial communications with team members, and customers to meet deadlines and minimize tool downtimes
• Use of small hand tools and multimeters to check output of ohms/voltage of thermal couples and heat trace connections
• Routine visual inspections and record keeping of materials used
• Familiar with peer/buddy work checking system to verify all completed work orders
• Assisting the VSG blue badge techs and engineers in Pump demolition, pump swaps & pump system upgrades/mods
• Trained to use 1/2 & full mask air purifying respirator
• Trained to work in permit & non-permit confined spaces
• A,b,c,d chemical training and safety
• Certified in use of fall protection systems- End user

● Wearing personal protective equipment according to customer standards on-site

● Following safety and clean room protocols and trained to be acutely aware of surroundings

●Accustomed to being in fab environment with free moving rebots and safety awareness

● Utilizing software to perform routine QA tests on equipment

● Performed standard installation of parts. upgrades and modifications on equipment following predefined task sets

● Use of schematics to interpret correct installations and repairs

● Following routine lock out, tag out protocols

●Trained to strip wiring with focused attention to sizing accuracy, terminal connection, and reconnection of electrical wires

●Trained to recognize and distinguish between SAE standard and JIS standard screw and bolt fittings

● Responsible for self-sufficient schedule for both remote and on-site job duties

● Maintain open lines of communication with other FSE, engineer in charge, and INTEL colleagues

● Weekly dock duties to facilitate arrival/unboxing of new incoming equipment

● Collaborate with team members to enhance customer experience, and drive customer retention

● Adherence to 6s safety protocols and procedures including but not exclusive to wearing personal protective equipment in FAB room environment

● Prioritized lots for maximum efficiency

● Writing recipes for new incoming product at critical metrology measurement layers and correcting recipes to run more efficiently

●Ability to find and pinpoint critical structures for metrology processes by reading photo mask

● Measuring critical sites and capturing still images of sites for review

● Review and analysis of collected data for numerical/visual anomalies

●Cross-trained in both Photo(primary) and Etch departments

● Troubleshooting Hitachi Scanning Electron Microscopes 8840 and 9200 equipment issues in two departments (photo\Etch)

● Administered routine QA maintenance tests and performing critical procedures to bring production equipment back from scheduled PM's, and tool resets/boot-ups

● Routine pass downs at shift change

● Recorded daily operations with emphasis on production holds at step that to be expedited and/or non routine changes

● Daily communications with department processing engineers to share necessary updates of procedural changes, processing trends/forecasts that are identified and collaboration on department improvements

●Certifications on cdsem tools, KLA, OVERLAY, and ADI(after development inspections)

Achievements:

●2021: Awarded 1 of 2 outstanding end of the year performance evaluations(supervisory election with approval from section manager)

●2021-2022: Lead an authorized independent initiative to develop and enhance written manual for the Hitachi Critical Dimensions Scanning Electron Microscope department with objective of facilitating the training and retention of new production specialists

• Managed daily operations on front end and back end
• scheduled weekly/monthly deliveries based on supply
• Created employees weekly schedules
• Facilitated communications between employees and owners
• Delegation of daily tasks and duties
• Resolved any escalated issues during daily operations