Luis Levario

• Connected wires to circuit breakers, transformers and other components.
• Installed, maintained and repaired electrical wiring, controls and lighting systems.
• Observed functioning of installed equipment or system to detect hazards and need for adjustments, relocation or replacement.
• Prepared sketches and blueprints.
• Tested circuit continuity to determine electrical compatibility and component safety.
• Repaired and replaced equipment, electrical wiring and fixtures.
• Fabricated and installed cable tray 6" -36', conduits 3/4" - 3" for low voltage, high voltage, control power, and instruments.
• Ran a crew of 25 electricians at one point for work on nights and worked elevated at times using lifts to complete work.
• Managed production, time, requests for scaffolding, and safety paperwork.
• Had daily morning safety meetings to go over our job assignments and safety hazards associated with those tasks.
• Communicated with field engineers and Phillips 66 plant reps to complete systems as completion dates approached.

• Fabricated and installed EMT, Supports, Mc cable, Lighting, pulled wire, and setup the raceways for conveyors in storage warehouses for corona virus vaccines.
• Installed lighting panels, DC backup systems, Generators, Transformers, and high voltage equipment in needed areas.
• Adhered to safety protocols, OSHA standards and building codes in installation of systems, operation of equipment and handling of materials.
• Evaluated existing electrical systems for maintenance, repair and update requirements.
• Performed troubleshooting to determine issues and appropriate action to complete tasks and provide quality installations.

• I fabricated and installed supports, conduit, stands, J-boxes, cable tray, and tubing tray for a Oxygen Compressor.
• Pulled high voltage and low voltage wires as need for power accessories, instruments and rtd's that were needed.
• Installed instruments such as pt's, rtd's, and worked on valves associated with the compressor.
• Installed stress cones on high voltage cables coming from the house to the compressor in the field, made proper testing on cables with the cooperation of the in house electricians and Saber.
• Made proper grounding installations on all pumps, motors, heaters, etc. as needed.
• Identified and terminated all cables from the mcc to the field, and did the final commission on the compressor.
• Fabricated, and installed tubing for samples coming out of the compressor, and feeder tubing for the valves.

• Fabricated and installed EMT, Supports, Mc cable, Lighting, pulled wire, and setup the raceway for assembly lines setup to build Tesla vehicles.
• Installed lighting panels, DC backup systems, Generators, Transformers, and high voltage equipment in needed areas.
• Adhered to safety protocols, OSHA standards and building codes in installation of systems, operation of equipment and handling of materials.
• Evaluated existing electrical systems for maintenance, repair and update requirements.
• Performed troubleshooting to determine issues and appropriate action to complete tasks and provide quality installations.

• Supervised crew of electricians and maintained safe, efficient and structured work environment.
• Resolved team and client challenges with proactive and actionable solutions.
• Communicated with clients to assess needs, provide status reports ad inform of any potential delays.
• Monitored employee performance and adherence to job specifications to maintain quality standards and high client satisfaction.
• Oversaw work of electrical and telecommunication personnel for key clients.
• Evaluated job scope and determined necessary supplies, timelines and projected expenses.
• Facilitated work site safety by applying knowledge of safety protocol and awareness of potential hazards.
• Monitored employees to enforce safety and work performance standards.
• Was in charge of a nightshift crew to complete workload associated with the shutdown of OP1 unit in LyondellBassel.
• Instructed Electricians and Instrument hands on projects associated with the compressor decks and the towers in the unit.
• Managed the demo and installation of control valves, and instruments, so the other crafts could do their part.

• Coordinated with vendors to identify and procure appropriate equipment necessary for project completion.
• Mentored junior engineers and new hires to better improve competency and efficiency of all staff.
• Monitored manufacturing operations of electrical devices for compliance with safety protocols.
• Monitored installation and operations to consistently meet rigorous customer requirements.
• Added or removed wire to shorten or lengthen lines, using various types of splices, connectors and clamps.
• Fabricated and installed conduit, cable tray, supports, underground pvc, and pulled wire for circuits and instruments.
• Operated equipment such as mini excavator, trencher, and skid steer for underground work.

• Monitored employee performance and adherence to job specifications to maintain quality standards and high client satisfaction.
• Supervised crew of electricians and maintained safe, efficient and structured work environment.
• Evaluated job scope and determined necessary supplies, timelines and projected expenses.
• Oversaw installation, maintenance and repair of power lines, electrical systems, fixtures and appliances.
• Supervised a crew doing the underground piping, grounding, wiring, fabricating & installing cabletray
• Work was on a compressor

• Installed, maintained and repaired electrical wiring, controls and lighting systems.
• Repaired and replaced equipment, electrical wiring and fixtures.
• Inspected transformers and circuit breakers for malfunctions.
• Connected wires to circuit breakers, transformers, and other components.
• Installed, tested and calibrated commercial electrical equipment to meet use demands.
• Located and addressed electrical connection issues such as frayed wires and worn insulation to prevent larger problems.
• Efficiently installed electrical systems and components with careful analysis of technical schematics and specifications.

• Worked on tubing for sample stations in cooling tower Areas
• Fabricated and installed screw pipe needed for sample stations
• Fabricated and installed tubing tray needed for

Supervised a crew fabricating, and installing cable tray in the OSBL areas at the Sasol Project. Read Iso's for precise measurements on installations of supports and cable trays.

Worked at a Praxair plant with new construction doing all the underground pipe and duct banks. Had to read drawing and coordinates for stub ups on duct banks and fabricated supports for pvc pipes. Worked in trenches, fabricated, heated, installed pvc as needed and tied down pipe for underground runs.

Worked at A pharmaceutical plant doing commercial work, installing receptacles, lighting, motion sensors, fire alarms, etc. Also fabricated and installed cable tray, conduit, supports, and setup equipment ground for gears that were flown into the buildings. Pulled cable and terminated communication and low voltage for PLC's, also worked on high voltage for transformers. Left that job due to a family member becoming gravely ill, had to be closer to home.

Worked on a Turnaround for the Phillips 66 plant, Mostly did temporary power for the MCC buildings. Hooked up disconnects for generators which supplied power for equipment in the Field, Did work on buckets and High voltage transformers. I was there till the end and was layed off once we were done, with the small shutdown.

• Fabricated specific electrical component parts and assemblies.
• Demonstrated expertise in the use of cable reels, stripping tools, voltage detectors, crimping tools and wire and cable cutters.
• Developed in-depth knowledge of arc flash ratings and standards.
• Measured devices, including analyzers, amp meters and volt-ohm meters.
• Worked with various types of cableways, conduits and other electrical raceways.
• Updated service record files on equipment drawings and history.
• Installed, tested and modified circuit breakers, controls, fuses, lights and motors.
• Recorded the respective measurements for each project.
• Consistently updated knowledge of safety requirements and policies.
• Maintained a working area that was clean, safe and stocked with appropriate equipment and supplies.
• Tested equipment tools such as oscilloscopes, ammeters and test lamps.
• Worked extended hours on weekday and weekend projects.
• Consulted with the supervisor electrician regarding the likely risks associated with the assigned job.
• Planned motor starter and control installations using codes and specs.
• Worked on new Analyzer installation which consisted in power distribution, Communications, Digital and Analog signals, and process sample tubing which consisted of its own heat tracing.

Worked as an electrical foreman for fabricating and installing supports, conduit runs, cable tray, electric heat tracing on pipelines, grounding, j-boxes and cabinets for power and instruments. Ran a crew for pulling wire to power and instruments to heat tracing splice boxes and control panels. Fabricated specific electrical component parts and assemblies. Interpreted drawings, wiring diagrams, flow charts and written descriptions of the project requirements. Worked with various types of cableways, conduits and other electrical raceways. Updated service record files on equipment drawings and history. Worked on Transformers supplying power to the Heat trace panels for proper and efficient use of tracing. Worked extended hours on weekday and weekend projects. Consulted with the supervisor electrician regarding the likely risks associated with the assigned job. Demonstrated expertise in the use of cable reels, stripping tools, voltage detectors, crimping tools and wire and cable cutters. Maintained a working area that was clean, safe and stocked with appropriate equipment and supplies.

Fabricated and installed supports, conduit runs, cable tray, lighting, receptacles, grounding, j-boxes and cabinets for power and instruments. Ran a crew for pulling wire to power and control power on motors, lighting panels, start stops , receptacles, lighting, also instrument cable to PLC cabinets, and substations. Ran quality control for instruments associated with loops in the PLC going out to the associated equipment that was needed.
• Installed, tested and modified circuit breakers, controls, fuses, lights and motors.
• Fabricated specific electrical component parts and assemblies.
• Interpreted drawings, wiring diagrams, flow charts and written descriptions of the project requirements.
• Worked with various types of cableways, conduits and other electrical raceways.
• Updated service record files on equipment drawings and history.
• Worked extended hours on weekday and weekend projects.
• Consulted with the supervisor electrician regarding the likely risks associated with the assigned job.
• Demonstrated expertise in the use of cable reels, stripping tools, voltage detectors, crimping tools and wire and cable cutters.
• Maintained a working area that was clean, safe and stocked with appropriate equipment and supplies.

Worked as a foreman on the Marathon oil and gas drilling pads in many different locations south of San Antonio. I ran a crew and we fabricated and installed supports, cable tray, lighting, receptacles, grounding, j-boxes and cabinets for power and instruments. Ran a crew for pulling CLX wire to power and control power on motors, lighting panels, start stops , receptacles, lighting. We also pulled wire for instruments on the drill sites and installed the instruments needed for certain equipment. Had to do work on electrical gears and buckets in the substations including pulling all the high voltage feeders for the transformers and motors. Fabricated specific electrical component parts and assemblies. Interpreted drawings, wiring diagrams, flow charts and written descriptions of the project requirements. Worked with various types of cableways, conduits and other electrical raceways. Updated service record files on equipment drawings and history. Worked extended hours on weekday and weekend projects. Consulted with the supervisor electrician regarding the likely risks associated with the assigned job. Demonstrated expertise in the use of cable reels, stripping tools, voltage detectors, crimping tools and wire and cable cutters. Maintained a working area that was clean, safe and stocked with appropriate equipment and supplies.