Luis Mejia

• Regular PM's, consisted of calibrating equipment, replacing if faulty.
• Worked on Auxiliary boiler, repaired gas valves and calibrated when needed. Fixed O2 sensor on aux boiler.
• Worked on Steam turbine and Gas Turbine
• Steam turbine work consisted of faulty air valves, faulty transmitters. Did a full tear down of the steam turbine, helped with the speed sensors and vibration sensor inside the turbine. Installed a junction box for new thermocouples. Removed all thermocouples and transmitters and reinstalled and calibrated.
• Gas turbine work consisted of faulty thermocouples and faulty air valves. Replaced and calibrated according to GRDA and compliance. During outage removed all blade path thermocouples. Disk cavities thermocouples, Bentley Nevada vibration sensors and reinstalled and adjusted/calibrated as needed. Helped take apart turbine on Major outage.
• Regular work on electrical equipment such as motors and lighting equipment.
• Worked on silos and fly ash, repaired and troubleshooted atomizers.
• Became proficient on there software's Ovation and Netmation, learned to read alarms and trend depending on what needed done. Adjusted valves or sent commands on GRDA request or to properly have plant running.
• After outage from end of February till end of May helped commissioned start up of plant.

• Calibrated and maintained instrumentation for optimal performance and compliance with safety standards.
• Diagnosed equipment malfunctions, implementing corrective actions to enhance operational reliability.
• Did commissioning on the plant and worked with engineers to make sure the equipment worked.
• 5 Point calibrations, loop test on transmitters.
• Installed new transmitters and replaced equipment that was faulty or broken.

• Installed and terminated a variety of equipment from MCC cabinets, HVAC units, UPS equipment, light fixtures, Fire alarm equipment, 480v Disconnects, 120V/240V panels, Transformers, Battery Racks, Bus Bars.
• Ran wire, Basket tray, cable tray
• Interpreted blueprints, schematics, and diagrams of project requirements and initiated appropriate electrical installations to customers satisfactions and electrical code.

Responsible for standard I&E work around a 35MW Biomass plant, including performing/troubleshooting of 480v breakers, and disconnects. Also maintaining the general electrical needs, checking motors doing regular PMs, fixing lights and checking transformers for the power plant. Assisted during an outage and helped in a variety of areas including mechanical.

• Terminated 480v motors-VFD's. Installed disconnects, lights, ran wire, conduit to code.
• Installed cable tray to specifications.
• Wore proper safety equipment on elevated surfaces to ensure work was done.

Responsible for the termination and troubleshooting of power distribution units. Ran wire harnesses, terminated and installed circuit breakers, performed electrical troubleshooting of breakers, and disconnects, torqued Bus-bars to specification. Point to point terminations. Read blueprints schematics to ensure accuracy of installation and performed functional testing.

• Ran hundreds of feet in wire, and conduit from 1/2 inch to 2 inch from EMT to Ridgid.
• Terminated a variety of equipment from MCC buckets to 120/480v panels, proximity switches, I/O cabinets, pressure switches, flow valves, PLC, 24v equipment.
• Commissioned at the end of project ensuring every device was working at specification, troubleshooted.
• Worked with engineers to ensure proper measures were taken.

• Ran 1/2-3 in Ridid conduit, terminated a variety of equipment. 480v motors, light switches, 120-480v panels.
• Terminated VFDs, sliding gates for a conveyer belt at the TAMKO facility. Hundreds of CAT wire, E-Stop brakes, HOA switches.
• Led troubleshooting efforts for complex electrical issues, ensuring effective solutions were executed.
• Interpreted blueprints, schematics, and diagrams of project requirements and initiated appropriate electrical installations.

• Ran conduit from 1/2 to 2 inch from customers prints to code. Installed junction boxes, terminated 120/240V circuits and lights. Terminated 120/240V panels with power with proper safety.
• Trained junior electricians on best practices and safety protocols in the workplace.
• Diagnosed issues and developed effective solutions.

• Installed and repaired electrical systems in a paper mill and limestone plant.
• Assisted senior electricians with troubleshooting and diagnosing electrical issues, as well as running new electrical conduit from 1/2 to 2 inch. New electrical wire for 480v motors and MCC cabinets. Terminated 480V motors and MCC buckets, including 120V panels.
• Followed safety protocols and maintained compliance with local electrical codes.
• Operated hand and power tools safely to perform installations and repairs.
• Read blueprints to customers satisfaction.