Summary
Overview
Work History
Education
Skills
Willing To Relocate
Timeline
Generic

Nghia Ly

Arlington,TX

Summary

Hardworking, eager to learn new skills and advance knowledge with hands-on experiences. Proficient in building hardware and advance interpersonal abilities.

Professional assembly worker prepared for roles in manufacturing and production environments. Known for delivering high-quality workmanship and maintaining efficiency on assembly line. Focuses on team collaboration and consistently meets production goals. Reliable, adaptable, and skilled in using various tools and machinery.

Experienced with assembly processes and techniques critical to efficient production. Utilizes strong attention to detail and manual dexterity to ensure accurate and timely completion of tasks. Knowledge of safety protocols and quality standards to maintain optimal workflow and product integrity.

Overview

8
8
years of professional experience

Work History

Assembler II

Transnorm Honeywell
09.2021 - 03.2023
  • Assemble conveyor or chute depended on order number
  • Read and deciphers schematics, blueprints and assembly instructions
  • Then select frame with ordered number, put it on stands, inspect it sometime need to deburr or tap thread again to secure part, then measure and mark it follow schematics
  • Pick up all parts with code number and put on the positions that marked on frame, then use hand tools and power tool to install parts and fasten it to frame
  • Put desk board on and align gaps on both edge equally
  • Install pulleys on both ends of conveyor and belts with order number and connect both trimmed ends by pins, align gap between vertical panel on both edges and adjust the tension of belt
  • Follow drive motor instructions, connect wires to motor to test speed, belt alignment, read the measure number of amp, voltage that is same allowance of manufacture and adjust the tension of belt again
  • If it is chute, check parts and select column with order number, measure and inspect the length and follow drawing instruction to determine where is the top or bottom to keep in critic allowance and beginning to build from here
  • The procedures including in hanging component parts by clamps, align it then drilling, tapping the holes, then check the length of chute and permitted allowance and fasten by screws and finish

Technician

Luraco TECHNOLOGIES
08.2019 - 08.2021
  • Assembly parts to a device, unit, module then perform complete massage chair and install software to test run
  • Service for customer's chair at their home repair some devices along with new units and replacement parts
  • Supplied production data to field operators, technicians, engineers and supervisors
  • Organized, analyzed and prepared technical data reports
  • Tested components, assemblies and systems to diagnose problems
  • Set up and verified functionality and availability of safety equipment

Electrical Apprentice

Feris Vo Electrical
02.2017 - 08.2019
  • Built controllers and panels to complete system installations, balanced phase loads
  • Completed semi-skilled and skilled work under supervision of fully qualified supervisors
  • Examined and tested and analysts electrical systems to locate losen, disconnected wire connections or other failed devices such as breaker, gfci, afci, shortage, ground fault, wrong wire gauge
  • Kept work areas clean, neat and free of hazards
  • Verified measurements and made accurate cuts to avoid wasting materials on job sites
  • Operated hand and power tools and diagnostic equipment to complete various aspects of jobs
  • Followed all relevant electrical and building codes for each job
  • Inspected existing wiring to identify problems such as short circuits

Sheet metal assembly and cancel operator

TranStar Aircraft Interior LLC
03.2015 - 12.2016
  • Read tape measures, drawings, diagrams and specifications for correct assembly
  • Assembled panels and products such as bolts, nuts, and special materials securely and accurately according to blueprints and specifications
  • Performed visual final inspections and documentation prior to assembly, resulting in 100% quality of products
  • Set and verified parts clearances to prevent jams or wasted materials
  • Inspected and tested final products to verify conformance to established tolerances
  • Checked parts against stock lists, blueprints and materials specifications to verify compliance with standards

Education

40 Hr Programming CNC - Computer Numerically Controlled (CNC) Machinist Technology

Mountain View College
Dallas, TX
08.2016

Associate in Science (AS) - Regional Planning

Saigon architect University
05.2000

Skills

  • Electrical Proficiency
  • SAP
  • Assembly
  • Welding
  • Machining
  • Blueprint Reading
  • Power tools
  • Quality control
  • Customer service
  • Enterprise Resource Planning (ERP) Software
  • Schematics
  • Mechanical Knowledge
  • Lean manufacturing
  • Standard power tool knowledge
  • Machinery repair
  • Diagnostics and troubleshooting
  • CNC Machining Expertise
  • Electrical maintenance and repair
  • Assembly and production
  • Problem-solving
  • Attention to detail
  • Repetitive work

Willing To Relocate

  • Dallas, TX
  • Irving, TX
  • Arlington, TX

Timeline

Assembler II

Transnorm Honeywell
09.2021 - 03.2023

Technician

Luraco TECHNOLOGIES
08.2019 - 08.2021

Electrical Apprentice

Feris Vo Electrical
02.2017 - 08.2019

Sheet metal assembly and cancel operator

TranStar Aircraft Interior LLC
03.2015 - 12.2016

Associate in Science (AS) - Regional Planning

Saigon architect University

40 Hr Programming CNC - Computer Numerically Controlled (CNC) Machinist Technology

Mountain View College

Similar Profiles

CREATE PROFILE
Nghia Ly