Nicholas Mongelli

• Facilitate general maintenance of Production lines.
• Maintain/repair Conveyor belts, Motor-drives, and Electrical systems.
• Install Gearbox, 120v-480v circuits, single-3 phase motors, water, and pneumatic applications/lines.
• Repair Sprockets, Chain Drives Tension Rollers, and Feed chains, while providing scheduled Preventative Maintenance.
• Monitor PLCs, VFDs, and HMI monitors.
• Performed electrical and mechanical repairs of production equipment to minimize downtime
• Completed daily, weekly, and monthly checklists on building equipment to maintain records of scheduled maintenance procedures

• Run 24v-480v Circuits.
• Run/Bend/install Conduit.
• Install/Fabricate Panels/Gutters/Raceways/Junction Boxes.
• PLC install, VFD/VSD install, and Controls.
• Read and interpret electrical, mechanical, and architectural drawings and electrical code specifications for wiring layouts.

• Operate ST-80, Floor Tongs, Operate PTS, and Wench Lines.
• Chemical handling/mixing, inspecting, and maintaining equipment.
• Perform mechanical repairs.
• Implementing company procedures.
• Making connections while drilling, digging ditches, and assisting in rigging down.
• Operated down-hole tools safely and responsibly, limiting risk.
• Maintained clean, organized, hazard-free work areas for optimized site safety.
• Used different machines and tools based on individual job requirements.

• Maintain reliability/Monitor machine operations on Production Packing Floor.
• Repair problematic issues relating to Allied, Volm, Matrix, Fox, Kwick Lock, Yamamoto, Lantec, Case Erectors/Baggers/Tag Printers/Check Weighers.
• Repair/ Replace belts, rollers, sprockets, gear drives, and single-3phase motors.
• Work/Install/ Troubleshoot Pneumatic Controls/Systems.
• Work/Install/Troubleshoot Electrical Circuits 24v-480v.
• Install/Repair Electrical Coils/Disconnects/E-Stops/Relays/ Transformers/Proximity Switch's/ Sensors.
• Set/Calibrate/Operate Machine HMI
• Pipe Fitter/Welder Helper
• Forklift Operator
• Planned layout and installation of electrical wiring, equipment, and fixtures based on specifications and applicable code.
• Read and interpreted electrical, mechanical, and architectural drawings and electrical code specifications for wiring layouts.

• Install Stainless/Carbon/Galvanized Piping-Fittings-Flanges.
• Fit/Cut/Thread/Buff/Grind- Stainless/Carbon/Galvanized Pipe.
• Bolt up, Lock Out/Tag out.
• Hydro/pressure test Gas/Steam/Water lines.
• Install single/three-phase motors.
• Install 2-3 way High-Pressure Pumps/ Actuators.
• Operate Forklifts/Man Lifts.

LINEMAN:

• Install/Service Step-up/overhead Transformers/overhead Capacitors/ Switchgears.
• Set Power Poles and Power Lines.
• Drive and Operate Line/Bucket truck w/ Auger.
• Service over head/Underground Distribution Power Lines of up to 60KV. Perform Cable Splices/ High Voltage Termination, Hot Sticking, and Pole Climbing.
• Knowledge of NEC code practices/OSHA Safety.
  

WIREMAN:

• Install/Service MCC Panels, Disconnects, and VFDs in Commercial/Industrial Applications.
• Install/Troubleshoot 3 phase-Single phase motors.
• Install/Troubleshoot/perform Diagnostics on Allen Bradley/Modicon PLCs.
• Install/Troubleshoot 24v-600v Circuits, Relays, and Controls.
• Install Conduit: (IMC, EMT, OCAL, Rigid, PVC, MC, BX, Flex/Seal Tight, etc.)
• Install T-Bar, Use of Power Tools, Knowledge of NEC Code/ Practices.
• OSHA Standards/Certification.