Randy Beaver

while running Tera Electric i would bid all incoming projects, budget jobs, and run a crew of 4 guys we did whole house rewires and and new construction Homes as wells as commercial jobs such as retail shops . I would do service calls for trouble shooting of various Electrical problems for Residential and commercial properties.

while working for tech usa i was placed at at factory in loudon tn called Primient contracted through Funderburk Electric.

At the Primient plant i worked as a journeyman Electrician installing Rigid conduit, updating and wiring new plc's, trouble shooting and fixing 277v lighting systems, installing 480v motors for various machine's as well as installing motor starters.

• Repaired and installed new fixtures, wiring, circuits, and motors.
• Assisted in training apprentice electricians, sharing knowledge, techniques, and best practices for success in the trade.
• Collaborated with other tradespeople to complete complex projects efficiently and meet deadlines.
• Performed troubleshooting to determine issues and appropriate action to complete tasks and provide quality installations.
• Interpreted blueprints, schematics, and diagrams of project requirements and initiated appropriate electrical installations.
• Completed rough-in, termination, and underground work.
• Read technical drawings, diagrams and project documentation to make accurate decisions about electrical system installations and repair work.
• Tested electrical systems and components for continuity, current, voltage and resistance.
• Maintained a clean and organized work environment, ensuring optimal productivity during electrical tasks.
• Verified problems, investigated faults, and troubleshot solutions to enhance installations.

At Terra electric I was part owner and a journeyman Electrician we did a lot of service work as well as

remodels and new builds both commercial and residential and some Industrial. I would lay the job out

plugs and switches where they go and then I would manage my apprentices and execute the work .I had

also put a Electrical Warehouse Stokes account in my name for financing. I ran all my own jobs mostly

medium size jobs I acquired financing did the work and billed for the jobs I was on and the jobs that my

fellow journeyman were working on.

• I installed and wired plc panels, transformers, pumps/motors, etc
• Worked from ladders, scaffolds and lifts to install, maintain, or repair electrical wiring equipment and lighting fixtures in ceilings, on roofs and on towers.
• In industrial houses for the oil industry
• The installation was class1 division 1 with explosion proof standards
• Installed and wired electrical transformers, service panels, and circuit breakers.
• Planned layout and installation of electrical wiring, equipment, and fixtures based on specifications and applicable code.
• Inspected electrical systems, equipment and components to identify hazards, defects, and repair requirements.
• Used testing instruments such as ohmmeters, voltmeters, ammeters, and multimeters.
• Read and interpreted electrical, mechanical, and architectural drawings and electrical code specifications for wiring layouts.
• Improved electrical system safety by conducting thorough inspections and identifying potential hazards.

• I accompanied Journeyman Electrician on service calls including troubleshooting faults in electrical systems, Installing and repairing electrical systems, Bending and installing conduit, Obtain precision measurements such as volt and ohm readings, Interpret blue prints, schematics and diagrams, Arrange fixtures and boxes for installation, Repair and install steffes electrical heating thermal units, Install and repair heat tape, use a bucket truck to repair light poles

• Working for Mountain Top Electric i started working as the company started a big hospital project in Casper Wyoming i dug ditches with mini excavators and installed pvc pipe for under ground electrical lines, I have used rc compactors as well as skid steers, later in the job i lated out hospital patient and surgery rooms for boxes and fixtures, Bending and Installing conduit

• I built single and duplex pump control panels that included layout and drill/tap back panels, device, motor starters, PLC equipment, etc
• Wired point to point connections and tested in quality control
• These control panels were built from engineered blueprints
• i Interpreted wiring schematics laying out devices

, Installing and wiring devices ranging from motor

starters to push button systems for factory's. and there was a high standard of quality.

• Wiring devices and fixtures, using bucket trucks to install wall packs running bobcats and skid steers, learning NEC codes