Robert Stashak

• Maintained accurate inspection records for future reference and quality control purposes.
• Reduced rework costs by identifying defects early in the fabrication process through diligent inspections.
• Promoted a culture of continuous improvement by actively participating in team meetings focused on identifying root causes of recurring issues.
• Increased overall productivity by monitoring welding processes, personnel performance, and resource allocation.
• Tested Welders
• Enhanced project efficiency by ensuring adherence to welding codes, standards, and project specifications.
• Tested welders for understanding of code and proficiency in different environments.

• Tested welders for understanding of code and proficiency in different environments
• Reviewed specifications in order to assess contractor compliance with design.
• Examined products for imperfections and defects.
• Followed standard operating procedures for inspections and tests.
• Maintained current knowledge of codes.

• Tested welders for understanding of code and proficiency in different environments.
• Recorded inspection and test results on data sheets.
• Examined products for imperfections and defects.
• Followed standard operating procedures for inspections and tests.

• Tested welders for understanding of code and proficiency in different environments.
• Maintained current knowledge of codes.
• Used Blue Beam to track data and write up results.
• Also worked at Appellation fab shop in Williamsport PA to observe and document fabrication for Wind Gap meter station.

• Tested welders for understanding of code and proficiency in different environments.
• Reviewed specifications in order to assess contractor compliance with design.
• Maintained current knowledge of codes.
• Used Microsoft to track data and write up results.

• Tested welders for understanding of code and proficiency in different environments.
• Used Microsoft Office to track data and write up results.
• Conducted inspections, tests and measurements of and materials to verify adherence with regulations and desired specifications.

Inspected at station #165 in Chatham VA . Tested welders and supervised welders

Performed asbuilt and red lines.

.Developed and maintained courteous and effective working relationships. Conducted inspections, tests and measurements of pipe materials to verify adherence with regulations and desired specifications.

Welding inspector,

Evaluated work against design specifications.
Administered tests to welders to assess understanding of the work and applicable code requirements.
Tracked information and authored daily reports.
Stayed up to data on current state, federal and codes.
Applied changes requested by designers, owners or inspectors.

Was responsible for testing of welders and supervising welders on the ROW and in Fabrication.Before welding started I supervised the unloading of 42" pipe and observed the cutting of the tree line on the Franklin loop .Kept weld information for the mainline and made all of the weld maps. Worked on hydro testing and fabrication.

Welding inspector for STS in Odessa Texas. Working on tie-ins and lowering in pipe.Observing contractor jeeping pipe . Working on firing line and front end on main line.

Welding Inspector working on hydro-test of 180 miles plus valve settings on 26 inch mainline from Carrolton Ohio to Albany Ohio. Working with chief Inspector on red line and also hydro reports.And close out boxes.

worked on a 42 " Palmorton loop job for chief Inspector Ronald Coker where I attended pre-job meetings.

I am the lead inspector and had two inspectors to delegate work to.

Tested 40 welders to API 1104 SMAW code.

Visually inspected welds and monitored preheating before and after welding.

Transferred and recorded pipe specification numbers off of pipe.

Filled out and recorded all welding certificate papers on the job.

Tested welders on the automatic welding procedures FCAW code. Certified welders on multi weld repair certification procedures and split tee procedures.

Worked with fabrication foremen on fabrication prints. Made red line drawings for fabrication and mainline .

Worked for cheif inspector Joe Dynda over spread 16. Assisted Todd Clack on testing welders on API 1104 SMAW code.

visually inspected welds, monitored preheating before and during welding. Transferred and recorded pipe specification number off pipes.

Pipe fabrication and welding, stick rod , tig , carbon and stainless.

Consistently assumed additional responsibilities and worked extended hours to meet project deadlines.

Welded in flat , horizontal , vertical and overhead positions.

removed and repaired unacceptable welds with an air arc and grinder to meet quality guidelines.

Worked with gas tungsten arc,gas metal arc,flux-core arc, plasma arc, shielded metal arc, resistance welding and submerged arc welding.

Fabricated shop parts directly from blue prints.

Used MIG gun arc to melt and deposit metal from electrode to work pieces.

welded carbon steel and hydrotested 36 inch pipe on pipeline for PG&E.

Welded on the firing line and also did tie-ins and fabrication.

Welded and fabricated and installed fabrication.

Pipe fabrication and welding stick rod, tig , carbon and stainless.