Scott Manges

• Reviewed blueprints and other drawings to identify correct grades.
• Removed old coatings from existing surfaces using abrasive blasting equipment.
• Operated a mixer truck and poured concrete on site.
• Can operate forklifts, Pettibone, scissor lifts, and JLG aerial lifts.
• Directed casting of concrete and supervised laborers using shovels or special tools to spread.
• Reshaped uneven edges on existing slabs using diamond blade saws or grinders.
• Removed rough or defective spots from concrete surfaces, using power grinder, or chisel and hammer.
• Repair cracks in concrete utilizing epoxy techniques.
• Drilled holes into existing walls for anchors used to secure fixtures.
• Repaired cracks in concrete by filling them with caulking materials or grout.
• Worked with teammates to move steel forms.
• Poured concrete into forms using pump hose and leveled.
• Grouted joints between precast pieces of concrete to create a water-tight seal.
• Applied hardening and sealing compounds to cure concrete surface.
• Mixed and applied epoxy coatings to floors, walls, and other concrete surfaces.
• Sealed newly patched areas with waterproofing agents or protective coatings.
• Maintained safety of work areas by adhering to strict regulations.
• Removed debris and waste to clean site after completing work.
• Shaped rounded edges on corners with edger tool and created grooves to control cracking.
• Finished surfaces by troweling, floating and brushing following project requirements and specifications.
• Installed formwork for pouring new concrete slabs, steps, curbs.
• Prioritized tasks for each job after reading project blueprints and documents.
• Used forklifts and other equipment to move materials and complete project work with construction team.
• Produced rough concrete surface using brooms.
• Installed anchor bolts, steel plates and other fixtures in freshly poured concrete.
• Spread, leveled and smoothed concrete using rake or shovel.
• Performed minor repairs on equipment when needed.

Q.C.

• Calibrated products to match design and operational specifications.
• Oversaw disposal of products, materials and equipment not in compliance with tolerances, safety standards, or quality levels.
• Tested hardened concrete for compressive strength, following ACI standards.
• Monitored wind, heat, and cold throughout the curing process.
• Adhered strictly to Good Manufacturing Practices guidelines at all times.
• Maintained records of all nonconforming products and completed corrective actions as required.
• Used specialized tools to take precise measurements of various aspects of samples.
• Conducted root cause analysis investigations when issues arose with production processes or end-products.
• Documented inspection results by completing reports and logs and summarizing and entering data into quality database.
• Identified production concerns and worked with supervisors to understand and remedy situations.
• Recommended essential corrective actions based on test results.
• Inspected and repaired products to meet project expectations.
• Analyzed plans, specifications and blueprints to understand product requirements.
• Identified areas for improvement in existing processes, procedures, and equipment.

• Mixing concrete using wheelbarrows and shovels as necessary.
• Removing excess mortar from between finished bricks or stones.
• Cleaned and prepared work surfaces with appropriate tools and solvents.
• Setting up scaffolding as needed on job sites.
• Cleaning surfaces prior to applying sealant or waterproof coating material.
• Carrying and mixing mortar, cement, and other construction materials to the work area.
• Calculated mixture ratios, angles and square footage to determine materials needed and plan layouts.
• Applied and smoothed mortar or other mixtures over work surface.
• Following safety protocols while working at height or with hazardous materials.
• Performing basic maintenance on tools used in masonry work.
• Using saws to cut blocks into specified shapes when needed.
• Loading and unloading supplies from trucks.
• Guided large stones onto foundation locations using truck cranes, hoists and skids.
• Kept work area clean and clear from debris to ensure I have a safe and effective work area.

• Inspected materials and equipment regularly to check for potential hazards and machine defects.
• Completed scheduled appointments on time to drive quality service.
• Filled out work orders, repair logs and maintenance plans to document work completed.
• Diagnosed problems and determined solutions for various customer issues.
• Collaborated with team members to complete projects efficiently and effectively.
• I navigated my way to new places, as we did work all over the tri-state area.
• Identified potential problems during routine inspections in order to prevent future infestation problems.
• Repaired faulty components such as motors, pumps, valves, switches.