Tyler Fine
Duncan
Summary
Oilfield professional with 4 years of experience in drilling operations, specializing in safety enhancement and operational efficiency. Qualified Floorhand with experience in drilling operations and equipment maintenance. Adept at multitasking various complex processes. Efficient and accurate troubleshooter and problem solver. Expertise in pre-job planning and hazard identification, ensuring compliance with safety protocols. Holds a CDL A license with hazmat and tanker endorsements, alongside strong mechanical knowledge for effective problem-solving in high-pressure situations.
Utility Locator Technician with 6 months of experience in accurately locating underground utilities, utilizing specialized equipment and electronic mapping systems to support safe excavation practices.
Overview
17
17
years of professional experience
1
1
Certification
Work History
Floorhand
Helmerich & Payne, Inc.
Okarche, OK
12.2024 - 05.2025
- I assist with day to day drilling operations, rig move, making a connection, slip-and-cut drill line, nippling up, nippling down, pulling back pipe in the board when tripping out, working the board tripping in, building stands in the mouse hole.
- I always make sure to Pre-Job-Plan and have everything staged out for the next process we will be completing. Whether its getting all the tools ready for slip & cutting the drill line or having all of the cement iron and cement head on the floor and ready to go once we finish running casing. Always being a step ahead makes the job much easier and safer for everyone involved.
- During safety pre-tour i am attentive to make sure i understand what operations we are currently completing on the rig and if there are any issues that need to be addressed. Any equipment that needs to be fixed or anything that needs to be adjusted to make drilling operations run smoother.
- I work safely, quickly, and efficiently to help drilling operations continue to run smoothly.
- I stage out collar clamp, slips, pipe wrench, and hammer before we trip out so that we are prepared for BHA once we pull the motor and bit.
Utility Locator Technician
ELM Utility Services
Phoenix, AZ
06.2024 - 12.2024
- I primarily located SW Gas utilities but occasionally would locate fiber & electric when needed. I averaged about 60-70 hours a week because i really enjoy the job.
- Accurately located underground utility lines using specialized equipment and techniques.
- Collaborated with construction crews to ensure the safe excavation of areas where utility lines were present.
- Performed regular inspections and maintenance on line locating equipment to ensure optimal functionality.
- Maintained detailed records of all located utilities, including their depth, type, and location.
- Responded promptly to emergency requests for utility line locates to prevent accidents or service disruptions.
- Utilized electronic mapping systems and blueprints to determine the precise locations of underground utilities.
- Identified potential hazards or risks associated with underground utilities during site assessments.
Floorhand
Helmerich & Payne, Inc.
Chickasha, OK
02.2022 - 06.2024
- I assist with day to day drilling operations, rig move, making a connection, slip-and-cut drill line, nippling up, nippling down, pulling back pipe in the board when tripping out, working the board tripping in, building stands in the mouse hole.
- I always make sure to Pre-Job-Plan and have everything staged out for the next process we will be completing. Whether its getting all the tools ready for slip & cutting the drill line or having all of the cement iron and cement head on the floor and ready to go once we finish running casing. Always being a step ahead makes the job much easier and safer for everyone involved.
- During safety pre-tour i am attentive to make sure i understand what operations we are currently completing on the rig and if there are any issues that need to be addressed. Any equipment that needs to be fixed or anything that needs to be adjusted to make drilling operations run smoother.
- I work safely, quickly, and efficiently to help drilling operations continue to run smoothly.
- I stage out collar clamp, slips, pipe wrench, and hammer before we trip out so that we are prepared for BHA once we pull the motor and bit.
Mortgage Loan Originator
Peoples Mortgage Company
Phoenix, AZ
08.2020 - 03.2022
- I am a licensed loan officer in 14 different states i help borrowers with a program we have called The Teacher and Nurse Next Door Program. The program helps people that work in these industries by providing them a realtor who contributes 20% of their commission to go toward the borrower's closing costs. The borrower also has an Account Manager who negotiates seller concession's on their behalf.
- I also help people go over the best loan programs depending on their situation. If they do not have substantial funds for the transaction we work with down payment assistance programs to help with their out of pocket expenses.
- Building relationships with other realtors and getting referrals from borrower's from providing an amazing customer experience.
- Analyzed financial information, credit reports, and loan documents to determine borrower eligibility.
- Generated leads and cultivated relationships with potential borrowers to drive new business.
- Negotiated terms and conditions with borrowers while adhering to company policies and lending standards.
Sales Representative
Progrexion
Phoenix, AZ
09.2019 - 05.2020
- Promoted into Inbound sales due to high performance after my first 90 days of sales. I was regularly attaining 100+ sales every 2 weeks.
- Call Center commission based selling credit repair via Lexington Law, Credit.com.
- Using leads gathered from people denied for Rent to Own homes, Personal Loans, and Auto Loans to sell credit repair services.
- Responded promptly to inquiries from potential customers via phone calls or emails.
- Collaborated with sales team to develop and implement effective sales strategies.
- Identified customer pain points and proposed tailored solutions that addressed their specific challenges.
Floorhand
Helmerich & Payne Drilling
Oklahoma City, OK
04.2018 - 08.2019
- I assist with day to day drilling operations, rig move, making a connection, slip-and-cut drill line, nippling up, nippling down, pulling back pipe in the board when tripping out, working the board tripping in, building stands in the mouse hole.
- I always make sure to Pre-Job-Plan and have everything staged out for the next process we will be completing. Whether its getting all the tools ready for slip & cutting the drill line or having all of the cement iron and cement head on the floor and ready to go once we finish running casing. Always being a step ahead makes the job much easier and safer for everyone involved.
- During safety pre-tour i am attentive to make sure i understand what operations we are currently completing on the rig and if there are any issues that need to be addressed. Any equipment that needs to be fixed or anything that needs to be adjusted to make drilling operations run smoother.
- I work safely, quickly, and efficiently to help drilling operations continue to run smoothly.
- I stage out collar clamp, slips, pipe wrench, and hammer before we trip out so that we are prepared for BHA once we pull the motor and bit.
Casing Technician
Franks International
Vernal, UT
02.2017 - 04.2018
- I ran casing for Franks International and I was on call 24 hours 7 days a week.
- My duties included rigging up the power tongs and all other necessary parts to run casing slips, elevators, bails, hoses.
- Working the floor and running casing typically 5 inch, 7 inch, and 9 5/8 inch.
- Made sure to always wear proper PPE and work efficiently and safely and watch out for safety hazards for myself and my co-workers.
- Consistently stayed proactive and looked for potential hazards that might slow down the process or get someone hurt and address them as needed.
- Safely rigging up all casing equipment and making sure to use a spotter if there is a blind spot due to racked back drill pipe that might make it difficult for the hoist operator to see. Especially when bringing up the bails & casing tongs.
- Always using a secondary hoist for bigger items like the power tongs or Casing Running Tool.
Laser Operater
Wilco Machine and Fabrication
Marlow, OK
05.2014 - 01.2017
- I was responsible for loading the table of the Mazak laser with sheet metal.
- I had to make sure that the nozzle on the laser was a perfect circle and also had to perform tape shots to make sure that the laser would cut a straight line.
- Made sure that the parts were cut correctly and did not have any slag (rough or sharp edges) on them.
- I put the specifications into the NC-computer on the laser and also double checked all of the cut settings.
- I made sure that the parts were cut out of the proper material (aluminum or steel). Also made sure that the steel was the correct hardness and density.
- I made sure that my area was always neat and in order.
- I helped others if they needed any help.
- I always worked safe and efficiently to make sure that I put out quality work.
Car Sales Professional
Byford Chrysler Jeep & Dodge
Duncan, OK
06.2012 - 01.2014
- I helped deck the keys and make sure that the vehicles were aligned in row.
- Helped customers select a car or truck that best suites there needs and their budget.
- Evaluated trade-ins to determine how much money we could give for the vehicle.
- Logged my customers into the computer database and also followed up with customers to make sure that their vehicle was running well and that they were satisfied with our performance.
- Logged trade ins and took them down to the used car lot.
- Called previous client's to see if they knew about the promotion that we currently had going on. Schedule them for an appointment to come down to the dealership.
Sheet Metal Apprentice
Halliburton Manufacturing Sheet Metal Dept
Duncan, OK
10.2010 - 05.2012
- I also helped on the 175-ton press brake often times i would take the parts i had just cut on the laser and take them over to the press brake and go ahead and help brake the part.
- I also deburred and stamped parts with the production order number and the stock number on each individual part.
- Whenever i completed a job i would then operate the forklift to either take it to the next operation or take it outside onto the dock.
- I also ran an NC punch machine that would punch out metal from the material to allow it to continue to the next station.
- I also ran the pipe saw to cut pipe to the desired length where i used a tape measure on a consistent basis in order to make sure my measurements were accurate.
- I also ran the drill press to drill holes into certain parts so that they could proceed to the next workstation.
- Read blueprints and diagrams on a consistent basis to make sure that my work was within the appropriate tolerances.
- Also i made sure that my workplace was clean and in order by sweeping up dirt, dust, and kept trash picked up around my area.
- I also maintained and serviced my machines by changing out blades and bands.
Electric Meter Technician
Sooner Meter
Duncan, OK
05.2008 - 10.2010
- I had a map with all the old dial meters in the area that i needed to replace with the new digital meters.
- I would go to customer's homes, knock on the door, and let them know that i was there to change their meter.
- I used a PDA to scan the new digital meters and get the read on the dial meter i was replacing.
- Load up my work truck each morning with boxes of digital meters at the electric co-op i was working.
- I was able to consistently install 70-80 meters per day and mainly used saw-sa, lineman, and my PDA in order to complete my work.
Education
Information Technology - Some college
University of Central Oklahoma
Edmond, OK01.2007
High School Diploma -
Duncan High School
Duncan, OK01.2006
Skills
Rig operations
Safety compliance
Equipment maintenance
Pre-job planning
Utility locating
Attention to detail
Problem solving
Effective communication
Time management
Job prioritization
Team contribution
Mechanical aptitude
Teamwork and flexibility
Preventative maintenance
Certification
- CDL A, 10/01/25, 10/31/29, N081775284, CDL A with no restrictions and doubles/triples, tankers, and hazmat endorsements.
- MLO License, 01/01/21, 12/31/27, 2017730, Passed SAFE exam on 01/06/2021.
- Oklahoma Motor Vehicle Commission Sales License, 06/01/14, 06/30/15, 21081, Former automotive sales license expired in June.
- Electrical Apprentice Card, 02/01/13, 02/28/14, Valid only while directly supervised by appropriately licensed person(s).
References
- Randall Powers, Albatross Roofing & Construction, Owner, (405) 638-0429
- Mitchell Mantzke, Helmerich & Payne, Pit Hand, (580) 583-9048
- Rick Sill, Helmerich & Payne, Toolpusher, (970) 644-0048
Personal Information
Timeline
Floorhand
Helmerich & Payne, Inc.
12.2024 - 05.2025
Utility Locator Technician
ELM Utility Services
06.2024 - 12.2024
Floorhand
Helmerich & Payne, Inc.
02.2022 - 06.2024
Mortgage Loan Originator
Peoples Mortgage Company
08.2020 - 03.2022
Sales Representative
Progrexion
09.2019 - 05.2020
Floorhand
Helmerich & Payne Drilling
04.2018 - 08.2019
Casing Technician
Franks International
02.2017 - 04.2018
Laser Operater
Wilco Machine and Fabrication
05.2014 - 01.2017
Car Sales Professional
Byford Chrysler Jeep & Dodge
06.2012 - 01.2014
Sheet Metal Apprentice
Halliburton Manufacturing Sheet Metal Dept
10.2010 - 05.2012
Electric Meter Technician
Sooner Meter
05.2008 - 10.2010
Information Technology - Some college
University of Central Oklahoma
High School Diploma -
Duncan High School