Tyler Hardeman

• Firewatch / hole watch / bottle watch

• Learn the rules and regulations on how to operate a fire exstinguisher

• Stay at job after 30 minutes of last spark

• Dock time for entering and exiting confined space areas

• Read gas detector

• Worked in a group, able to communicate well thoroughly

• Greet others that didn’t know what exactly they were supposed to install

• Climb scaffolds, worked in high areas, supply tools, able to measure pipe and insulation

• brush and roll , spray paint and abrasive blasting on pipes and vessels

• Equipped thinner, sand paper and used three composition paint coating

• Installed Insulation(calcium on pipes) , perlite , aerogel , foam glass

• Installed insulation on steam lines, put on 90 degree, wrap metal on insulation

• Installed banners, put on cocing so water doesn’t get inside the metal onto the insulation

• Brush and roll , spray paint and abrasive blasting on pipes and vessels

• Equipped thinner, sand paper and used three composition paint coating

Installed Insulation(calcium on pipes) , perlite , aerogel , foam glass

• Run conduit 1/2-3
• Bend conduit 1/2-3, EMT 1/2RTD and power, pull wire, offsets, deducts
• Ground wire #2, #4, #6, #8 & #10
• Install cable tray, install boxes, run wire to Movs, audit control panels, PVC duct banks, use fish tape for cable wiring #8, #10 and #12
• Bend stubs 90s, 4 point saddle
• Aluminum rigid
• Installing boxes
• Install holes 1/2 in-3in \ knock out into J-boxes
• Install flex connectors
• Closing end caps and plugging end of tubing
• Terminate single pair wires
• Install plastic and stainless tie wraps with tie wrap gun
• Swag tubing .49, .65 and .83

• Run conduit 1/2 - 3 , threading and reaming

1224, 535, greenlee, chicago bender, big shot

• RTD and power , pull wire , offsets , deducts, 120v/208v

• Install cable tray , install boxes , run wire to motors , audit control panels , install heat tracing

• bend conduit, EMT 1/2 , install flex , PVC ductbanks , use fish tape for cable wiring #10,#12

• install heat tracing

• bend stub 90s , 4 point saddle

• Aluminum , rigid

• mc cable

• ground wire #2,#4,#6,#8

• glanding crx cable single pair 2/c

• install holes 1/2-3 in. / knockout into j-boxes

• install cables, crx cable, marine cable

• glanding cables, install punch tray

• closing end caps and plugging end of tubing

• terminate single pair wire

• swag tubing .49, .65, .83

• install teflon on plugs

• install pvc and emt

• pulling cable 3 conductor , 2 conductor and single pair

• install cable in cable tray properly

• Worked from ladders, scaffolds and lifts to install, maintain, or repair electrical wiring equipment and lighting fixtures in ceilings, on roofs and on towers.
• Installed and wired electrical transformers, service panels, and circuit breakers.
• Terminate junction boxes
• Install wall and stansion lights
• Install wall lights
• Install PVC for grounding
• Panel installation
• start / stop switches
• bucket boxes in the mcc
• install supports
• install conduit 3 point saddles & 4 point saddles
• bend 90s and install EMT
• Rigid
• aluminum

• Installed, maintained, repaired, and tested equipment for electricity generation and utilization.
• Planned layout and installation of electrical wiring, equipment, and fixtures based on specifications and applicable code.
• pull wire from single pair all the way to big red , 500KV
• Install tripezes supports
• Crimped grounding
• install clx & marine cable
• Install glands & covers for fittings
• install drains and plugs into boxes / panels
• Install cable tray , snap track
• knowledge of bending 90s on cable tray. Install dividers into cable tray. Installed PT’s , FT’s , PG’s , TT’s & PDTs.
• Terminated MOVs
• install flex from sizes 1/2 - 1 inch. Able to read blueprints
• knowledge of elevation
• Knowledge on using the knockout set and Whitney punch
• install a switch gear and transformer X0 , X1 , X2 , X3 H0 , H1 , H2 , H3.
• install duct seal on fittings that have potential explosion
• 535 greenlee bender and hand bender for EMT. Install ring terminals & kerneys & c crimps onto grounding on #2 , #8, #10 , #12 , 2/0 , 1/0 & 4/0