Adam Motes

• Retrofit Split systems

• New home Build out

• Upflow, Downflow and Horizontal split systems

• Complete drains

• Low voltage wiring

• High voltage wiring

• Seal floss copper with low pressure nitrogen to ensure no soot buildup

• Pressure test with Nitrogen to ensure no leaks

• Pull vacuume to desired Microns

• Startup Of new system and ensure it is working properly

• Check TD's and add refrigerant as needed.

• Calibrated equipment and educated customers on proper use and care.
• Met with customers to discuss projects and special requests.
• Completed paperwork, issued invoices, and accepted payments.
• Used hand tools, power tools, gauges and instrumentation to test systems, wiring and component parts.

• Install New Rtu's.

• read Blue Prints and spot Curb

• Weld angle iron for bracing

• Cut holes in roof for drops

• Set curb and drops for ductwork inside

• Set RTU'S crane and Helicopter as needed.

• Read Blue Prints and run ductwork accordingly.

• Put together square duct, ductmate, round pipe, spiral and double wall spiral.

• Finish out with flex duct and 2x2 grilles.

• Install minisplits and pumps for I.T. rooms.

• Comfort Controll Air Ballance.

• Run New Thermostat wires

• Replace Thermostats

• Startup Of new RTU'S

• Troubleshoot brokedown RTU'S and repair.

• Pressure test with Nitrogen

• Soft sauter and seal floss 3/8 - 2 1/4 copper.

• Install and duct Exhausts

• Followed established procedures for inspection of belts, drives and motors, performing needed maintenance.
• Diagnosed and repaired problems with electrical and mechanical systems.
• Tested systems, noting issues and completing preventive maintenance.
• Installed new equipment and explained operation and routine maintenance protocols to customers.
• Adhered to safety protocols and policies to reduce workplace hazards.
• Responded to problems reported by customers by troubleshooting and resolving hardware and software issues.
• Worked with diverse types of weather and ground conditions.
• Scissor lift, duct jack, extension ladders, 6 ft -14ft ladders

• Evaluated systems according to predetermined checklist and noted issues.
• Diagnosed and troubleshot problems, repairing, and restoring machines to peak performance.
• Inspected equipment to diagnose operational issues.
• Explained diagnostic findings to customers and outlined repair or service options.
• Installed new equipment and explained operation and routine maintenance protocols to customers.
• Adhered to safety protocols and policies to reduce workplace hazards.
• Responded to problems reported by customers by troubleshooting and resolving hardware and software issues.
• Maintained accurate records of service calls and customer interactions for training and accountability purposes.
• Responded to customer inquiries quickly and professionally to increase satisfaction.
• Replaced faulty components on computer systems and performed preventive maintenance to secure smooth operations.
• Demonstrated to customers proper methods for operating equipment after it had been installed.
• Managed maintenance activities, supervised staff, and inspected equipment.
• Completed preventive maintenance on machines to enhance production and maintain quality.
• Maintained strong focus on safety and efficiency to provide comprehensive support to personnel performing skilled repairs.
• Tended to machines, troubleshot malfunctions and completed basic repairs to keep equipment fully functional and well-maintained.

Retrofit Split systems

• New home Build out

• Upflow, Downflow and Horizontal split systems

• Complete drains

• Low voltage wiring

• High voltage wiring

• Seal floss copper with low pressure nitrogen to ensure no soot buildup

• Pressure test with Nitrogen to ensure no leaks

• Pull vacuume to desired Microns

• Startup Of new system and ensure it is working properly

• Check TD's and add refrigerant as needed.

• Calibrated equipment and educated customers on proper use and care.
• Met with customers to discuss projects and special requests.
• Completed paperwork, issued invoices, and accepted payments.
• Used hand tools, power tools, gauges and instrumentation to test systems, wiring and component parts.

• Retrofit Split systems

• New home Build out

• Upflow, Downflow and Horizontal split systems

• Complete drains

• Low voltage wiring

• High voltage wiring

• Seal floss copper with low pressure nitrogen to ensure no soot buildup

• Cut in new Supply and return air boots

• Pressure test with Nitrogen to ensure no leaks

• Pull vacuume to desired Microns

• Startup Of new system and ensure it is working properly

• Check TD's and add refrigerant as needed.

• Calibrated equipment and educated customers on proper use and care.
• Met with customers to discuss projects and special requests.
• Completed paperwork, issued invoices, and accepted payments.
• Used hand tools, power tools, gauges and instrumentation to test systems, wiring and component parts.
• New RTU installs
• Read Blue Prints for system placement ductwork.
• Spotted curbs and cut holes for square duct .
• Installed square duct, round pipe, spiral and duct mate accordingly.
• Installed flex duct to supply and return air grilles

• Retrofit Split systems

• New home Build out

• Upflow, Downflow and Horizontal split systems

• Complete drains

• Low voltage wiring

• High voltage wiring

• Seal floss copper with low pressure nitrogen to ensure no soot buildup

• Cut in new Supply and return air boots

• Pressure test with Nitrogen to ensure no leaks

• Pull vacuume to desired Microns

• Startup Of new system and ensure it is working properly

• Check TD's and add refrigerant as needed.

• Calibrated equipment and educated customers on proper use and care.
• Met with customers to discuss projects and special requests.
• Completed paperwork, issued invoices, and accepted payments.
• Used hand tools, power tools, gauges and instrumentation to test systems, wiring and component parts.
• New RTU installs
• Read Blue Prints for system placement ductwork.
• Spotted curbs and cut holes for square duct .
• Installed square duct, round pipe, spiral and duct mate accordingly.
• Installed flex duct to supply and return air grilles

• Retrofit Split systems

• New home Build out

• Upflow, Downflow and Horizontal split systems

• Complete drains

• Low voltage wiring

• High voltage wiring

• Seal floss copper with low pressure nitrogen to ensure no soot buildup

• Cut in new Supply and return air boots

• Pressure test with Nitrogen to ensure no leaks

• Pull vacuume to desired Microns

• Startup Of new system and ensure it is working properly

• Check TD's and add refrigerant as needed.

• Calibrated equipment and educated customers on proper use and care.

• Met with customers to discuss projects and special requests.

• Completed paperwork, issued invoices, and accepted payments.

• Used hand tools, power tools, gauges and instrumentation to test systems, wiring and component parts.

• Complete drains

• Low voltage wiring

• High voltage wiring

• Startup Of new system and ensure it is working properly

• Check TD's and add refrigerant as needed.

• Calibrated equipment and educated customers on proper use and care.
• Met with customers to discuss projects and special requests.
• Completed paperwork, issued invoices, and accepted payments.
• Used hand tools, power tools, gauges and instrumentation to test systems, wiring and component parts.
• New RTU installs
• Read Blue Prints for system placement ductwork.
• Spotted curbs and cut holes for square duct .
• Installed square duct, round pipe, spiral and duct mate accordingly.
• Installed flex duct to supply and return air grilles

• Pull and Replace Hmmwv, LVS and 7 ton Engines

• Pull and replace Body wiring harness

• Pull and replace Hmmwv transmissions, transfer cases, heads, head gaskets, injection pumps

• tire change outs