STEVEN CONRAD

• Installed various devices (routers, switches), ran, dressed, dropped, and trouble shooting Copper cables (with a fluke tool).
• Ran, dressed, dropped, and troubleshot smf mmf.
• Correctly plugging in Copper and fiber cable utilizing a p2p (point to point).
• Utilize VFL to assist in troubleshooting fiber optic cables.
• Navigate through patch panels to get to another location as easy as possible.
• Maintained all devices in the data center.
• Use of itracs to digitally mimic the entire data centers devices.
• Communicate through teams and email with other groups to solve a problem.

• Installed smoke detectors, notification devices, attach pipes to walls and ceiling beams, installed 4sq boxes on walls and in ceiling tile, pulled electrical wires to device location to be terminated into the devices.

• Pull, ran, dressed, terminated, tested, labeled cat 5 cat 6 cables, installed J Hooks on the wall. Maintain clean and safe work environment. Installed grid wire in ceiling using a hilti gun.

• Pulled speaker cable, installed speakers for school system in SC. Maintained a clean and safe work environment. Terminated, tested, trouble shoot cables and speakers.

• Pulled, ran, and dressed cables. Built out closets. Installed supports for the cables/J Hooks. Terminated, tested, and trouble shoot cables. Maintain a clean and safe work environment. Pulled underground fiber as well.

• Installed poles in the ground with concrete for mounting the access points, dug trenches for flex conduit for the electrical wires, mounted boxes on poles and H frames for equipment, installed surge suppressors, switches, ground bars/rods, battery back upstairs, grounded all pieces of equipment to ground rod/ bar, mounted access points on the sides of buildings, used rodders, fish tapes, and shop vac to find pathways in existing pipe underground

• Operated boom lifts to run data cables, ran conduit from ceiling to floor for data cables. Terminated, tested, and dressed cables. Terminated at patch panel.

• Built racks, installed patch panels, installed access points, ran cables for access points and wall drops. Terminated at location and at patch panel.

• Assembled brackets for mounting access points, ran data cables to access point locations from cabinets, terminated, tested cables, operated scissor lifts

Assembled and installed mounting brackets for waps.

Installed waps.

Ran and terminated the cat 6 cable in both the closets and in the field.

Neatly dressed the cables in the closets prior to terminating. Anything else you can think of that would sound good.

Utilized scissor lifts and boom lifts.

• February 2018 Title: Cable Technician II Job Details: Network cabling in a state owned psychiatric facility(Pulling and termination of Cat5 and Cat6 cable. Installing and terminating speaker systems and paging. Closet build outs, as well as terminations and installation of 110 blocks. Ability to read blueprints for accurate readings of cable paths(RCPs, Telecom Prints, Riser Plans)
• Broughton Hospital

• Title: Installation of PDU systems in a data center environment. Installation of Copper Jumper Cables for network routing. Installation of Fiber backbone as well as Fiber Jumpers for server installs. Server set up when needed or requested by customer. Unit powering and Rack installation. Termination of Cat6, Cat6a, Cat5 cabling. Installation of Cat6 Cabling, as well as dressing and termination of backbone. Termination of Copper using various RJ jacks.

• Title: Job Details: Termination of Cat6, Cat6a, Cat5 cabling. Installation of Cat6 Cabling, as well as dressing and termination of backbone. Termination of Copper using various RJ jacks. Testing of all copper cabling using a Fluke tester. Installation of Single Mode and Multi Mode fiber optics. Installation of Unistrut, Fiber Trays. Basket trays, Waterfalls. All thread rods. Inventory counts, as well as ordering necessary materials for the job. Following standards to ensure minimal material waste. Equipped with all necessary tools for the job. OSHA Compliant, as well as meeting all safety standards.

• Title: Painter Job Details: Closed holes, cracks using fillers Protected surfaces during painting by covering surface with proper paper. Maintained surfaces by washing with solutions and pressure. Cleaned equipments and tools on daily basis to avoid corrosion. Responsible for the duty of performing tasks which are not in schedule. Refinished fixtures for example chairs, benches, tables and other. Repainted the old objects such as machines, tools, equipment. Prepare surfaces of sheetrock, wood, metal, and masonry. Apply prime and finish paints, varnishes, lacquers and other covering materials(such as wallpaper) with brush, roller, or spray gun. Painted walls, machines, tools of given construction. Mix and match paint; recommend blending, harmonizing, and contrasting colors
• Palmetto Properties

• Title: Brick Grader Job Details: Maintained all OSHA and safety compliances Performed quality inspections on all manufactured products; thoroughly checked for any defects Stacked roughly 25, 000 bricks into a Mono-Rail each day Cleaned and maintained all equipment and materials
• General Shale