Junior Malau'ulu

• Performed component-level troubleshooting and repair of circuit boards to resolve hardware issues
• Utilized specialized tools and equipment to solder components and replace faulty parts
• Implemented quality control measures to ensure the reliability and functionality of repaired devices
• Maintained a clean work area to promote efficiency, organization, and safety during repairs
• Developed efficient workflows for diagnosing common device issues to improve turnaround time for repairs
• Documented all repairs performed, including details of the issue encountered, steps taken for resolution, and any replaced components or parts used

Nokia/Lucent/Alcatel (Building 1373) - Assistant Technician - Bench Tester Dept. #483

• Retrieve incoming Remote Radio Head (RRH) Unit from the warehouse into Bench Testing/Repair area.

Unbutton/Remove Screws to Outer Shell/Cover on each RRH Unit, Rubber Grommet, Port/Connector Covers,

Screws to Power Connector Covers. Inspect, verify and determined if there are any physical damage to any

Connectors or Ports. Any Damaged Connectors/Ports are deemed Unrepairable and automatically tagged and put on "Repair Cart".

• Non Physical Damaged Units can proceed to Pre-Testing. Determine Unit Type and Log-in to Bench Tester and follow procedures. Determine Failure/Pass upon completion of Bench Test and send to the following accordingly: MOD, Repair, jm" and place each unit to designated Labeled Carts. verify and ensure each unit(s) are logged into the system and saved accordingly.

Receive, inspect, verify and determined if incoming unit(s) are deemed: Passed, Damaged, Repairable or

Unrepairable and placed in predetermine location as per company procedures.

• Verify any water damage, voltage, continuity, physical appearance for quality etc. prior to placing them on the production line.

• Receive, inspect, verify and determined if incoming unit(s) are deemed: Passed, Damaged, Repairable or

Unrepairable and placed in predetermine location as per company procedures.

• Verify any water damage, voltage, continuity, physical appearance for quality etc. prior to placing them on the production line.

• New Cisco WiFi Equipment & Cabling: Remove and replace ceiling tiles and Run Cat6e Ethernet cables to install new Wifi at Kutztown University athletic building. Removed all existing Wifi equipment & Cate5 cables and replaced with New Cisco Wifi equipment.
• AT&T DAS Project (Pittsville, PA): Ran ¼" RF Coaxial cable through-out warehouse facility for DAS antennas and splitters. Using aerial lifts and Boom lift due to ceiling heights above 20ft.
• Verizon DAS Project (Bethlehem, PA) Ran ¼" RF Coaxial cable for new DAS antennas and splitters.

Throughout the new Zillow Warehouse facility. Using aerial list and Boom lift due to ceiling heights above

20ft.

• Verizon DAS Project (Wilmington, DE): Ran ¼" RF Coaxial on three floors in two buildings at various designated Telecom closet in each buildings, Ran Fiber in different buildings, mounted 26 DAC Antennas between buildings combined.

• Mounted and secured server cabinets as well as installed Nokia server equipment & hardware into cabinets.

Labeled, ran, laced, secured, and dressed all DC power & LAN cables onto designated cable racks from Nokia

Cabinet location to customer BDFB & Demarc location.

• Completed and cleaned up the QA audit list. Trace and verify fiber cables from Nokia Traffica cabinet to customer Fiber Demarc location.

Kept department overhead costs down and actual projects on time and on target. Coordinated & streamlined the staging process, configuration, testing, and shipment of all Cisco 3745e & 3845e routers/switches (DC),

SUN Netra240 & Netra T5220 (AC/DC) for "End of Life" (EOL) swap-out project. Staged approximately 5 markets a week for Tier I & II and International customers.

• Coordinated and conducted project initiation for on-site visit(s) with customer local switch personnel & project manager (PM) and secured Terminal Server, T1 cabling & termination projects at various customer sites.
• Worked with project managers (PM) on project scheduling along with Supply Chain Management (SCM) on project procurement thru SAP. Coordinated with install teams on projects: schedule and timeline as well as project quality & safety through-out duration of various project(s).

oordinated with Equipment manager, supply chain management (SCM) & Mechanical Engineering on identifying various network equipment and hardware which enabled providing the "Network Bill of Material"

(B.O.M.).

• To keep and cut cost down, researched and purchased various tools thru SAP that would support ongoing staging as well as field network installation.
• Coordinated and initiated internal cross-training of the TruePosition TPLP as to how it would be installed in the field at the customer facility to all staging team members. This included Switch Operations, Field

Operations, and Optimization, Technical Assistance Center (TAC) and some members of R&D.

• TPLP Network - Staged, configured, and tested multiple equipment & hardware prior to shipping. Assisted warehouse in packing equipment & hardware in preparation for shipment.
• Provided on-site installation of the TPLP Network at customer facilities. Conducted on-site walks with customer prior to and completion of installation for final sign-off.
• Troubleshoot DC power and communication circuits (DS0-DS3). Wire wrapped DSX patch panels, 110 punch down RJ45 patch panels