Michael D. Aguirre

Perform pneumatic and hydraulic acceptance (ATP) and qualification (QTP) testing of flight hardware and document results in a clear, precise and complete manner

Work with high-pressure pumps and high-pressure gases such as helium and nitrogen

Use mechanical hand tools and torque wrenches to layout, fabricate, assemble, and install experimental/production flight hardware for mock-ups, full-scale operating models, and test assemblies

Use basic and advanced electronic test equipment/software to run performance tests on parts

Analyze and interpret test data to meet acceptance criteria established by engineering

Work with design engineers to troubleshoot failures of parts and test equipment. Repair or replace flight hardware due to engineering design changes and test failures

Responsible for preventative maintenance activities on test equipment and data acquisition systems

Directed turbine engine component assembly and disassembly processes, ensuring accurate handling and proper process completion.

Interpreted blueprint schematics and component manual instructions to complete repairs and assess relevant parts.

Evaluated heat exchanger valves, oil regulators, and mechanical components for condition assessment and functional verification.

Evaluated component operating capabilities and sourced replacement parts to assemble units for operational return.

Performed electrical motor resistance tests and executed functional testing procedures to verify motor performance.

Investigated root causes of technical issues and determined key factors required to finalize units for quality review.

Managed pressure testing and performance testing of process units to assess functioning capabilities.

Assessed equipment failure causes with engineering teams and informed decision-making to enable timely processing solutions.

Coordinated complaint processing and followed internal administrative procedures to support resolution activities.

Operated electron beam welding equipment to join materials and maintain weld quality standards.

Maintained quality across every component while exercising airworthiness verification for aircraft and equipment as a certified mechanic.

• Operated vacuum furnaces and conducted furnace inspections to maintain equipment performance.
• Loaded and unloaded parts into furnace to support brazing and heat-treating processing requirements.
• Evaluated parts using conformance indications and completed inspection activities to confirm required standards.
• Analyzed blueprint drawings, then manufactured and brazed heat exchangers according to documented requirements.
• Applied alloying to parts and followed brazing preparation requirements per provided instructions.
• Utilized wrenches, grinders, and calipers to prepare parts and fixtures to support assembly operations.
• Performed detailed review of work order requirements to support end-to-end quality control across processing steps.
• Achieved precise brazing results by carefully preparing joint surfaces and applying appropriate flux.
• Set up torches, fixtures, and brazing materials for consistent joint preparation and process control.

• Supported heat treat department operations for raw materials and finished products.
• Operated Vacuum furnaces and conducted SAT’s.
• Loaded and unloaded parts into and out of the furnace with lifts and cranes.
• Maintained clean and organized work area, ensuring compliance with safety standards.
• Conducted Brinell and Rockwell testing on test pieces per conformance specs.
• Reported and deviation in parts process to engineers.
• Transported parts to different departments and reviewed work orders instructions.
• Contributed to a productive work environment to consistently meet parts demand.
• Job Qualifications:

• Set up survey racks to perform temperature uniformity surveys while maintaining compliance with AMS2750G and Nadcap requirements, including support during Nadcap audits.
• Utilized calibration instruments to calibrate recording controllers and load channels and verify proper operation.
• Tracked probe intervals, recorded interval changes, and updated schedules as required per AMS2750G.
• Verified temperature accuracy and validated load channel readings for reliable system performance.
• Monitored furnace performance and heat treatment conditions to achieve specified material requirements.
• Designed load maps to visualize and maintain parts flow within production operations.
• Managed loading and unloading of parts from racks per load map requirements.
• Executed Brinell or Rockwell hardness measurements on required materials to maintain inspection readiness and quality control.
• Applied knowledge of furnace components and furnace functions to support equipment operations.
• Worked with QA to compile and submit heat treat certificates and surveys for furnace qualification verification to continue production.
• Work with maintenance and engineers to update them on how furnaces are functioning and/or update them if there’s a malfunction or need repairs.
• Job qualifications.

• Supervised workforce activity and managed work orders to ensure consistent workplace operations.
• Managed furnace operations and temperature controls through probe and load coupler monitoring, including furnace loading and unloading activities.
• Executed quenching and follow-on performance requirements, ensuring compliance with parts specification requirements.
• Communicated critical information to workers for job task execution and coordinated with team members to uphold a safe working environment.
• Demonstrated operational knowledge of forklift, crane, welding equipment, and hydraulic component systems to support safe equipment operation.
• Applied furnace function expertise with strong mechanical aptitude for reliable operation.
• Performed welding and grinding on parts and applied knowledge of part inspection procedures to verify workmanship.

• CTE courses; computer/graphic design
• Pyrometry Certificate
• Certified Airworthiness Mechanic
• Certification of Electrical Introduction(LATTC)