Miguel Martinez

Installed 4-inch rigid conduit from MCC to the new location, which was about 400 feet away towards the new air compressor; 3C 3/0 was used to power up the motor. Mounted PLC and VFD panels in the MCC to get readings from the new compressor. Also helped out rig electrician with installation of new VFD and PLC upgrades. Installed channel tray and fabricated cable field tray routes for several 24-pair cables. Gland and terminate all control wires. Work extra hours to get the job done safely and on time, before the holiday. job in G.O.M. is complete.

Las Flores Canyon Sabal Oil Company. I began my job by walking down routes for fiber optic cable pulls. Mounted panels to house fiber splices helped with conduit installation. Ran cables in cable tray raceways by manlift. Knock out holes in walls sealed with fire-retardant foam, and route cables in the comm room toward the fiber splice box, all splices being able to pass inspection. After the job was completed, I was sent offshore near the Santa Barbara, California coastline to assist with the instrumentation and upkeep of offline well panels, clean, and replace rubber grommets. And walk down job for future fiber optic cable pulls and chemical skid tubing routes.

• Documented nonconformities and recommended techniques for prompt resolution.
• 2024 Citgo refinery shut-in.
• I and E inspections generated work packages for I and E techs to walk down instruments throughout the refinery. Once packages are completed, I would walk down with the client, Citgo would approve, and accept job completion. I did most of the work in one unit and assisted other QA inspectors with paperwork.

• TESLA: Install new 1-inch EMT conduit rerouted inside the MCC for the AHU; the unit was right above the high-voltage switchgear, so the unit needed to be relocated for fear of a water leak on the unit.
• Demo out old 1-inch conduit and wire, upsized wire from 3C10 to 3C8 for water heaters at sinks near clean rooms at Tesla.
• Mounted PLC and RIO panels at floor level, below the new AHU. Routed conduit toward the AC unit for field instruments. Pulled 24 pairs from PLC towards AHU control JB. Demoed out old Cat-6 cables and eliminated old conduit.
• Once the job was completed, a walkdown with the Tesla commissioning team for inspections was conducted.
• Built, calibrated and maintained electrical instruments used in design development processes.
• Tested energized and de-energized circuits, following test procedures and assisted in specialized test procedures.
• Worked closely with other technicians to complete projects efficiently.

• kentucky...papermill.
• Short conduit routes for control wires and power cables from #10 up to 3c500 MCM.
• Pulled cables routed to their correct MCC buckets, knocked out holes, glanded, megged all cables, and terminated.
• Later, I was moved to the QA/QC department to inspect all motor terminations and assist with the startup.
• Supervised electrician control room modifications, maintaining complete understanding of work scope, safety and documentation requirements.
• Ensured that all personnel onsite adhered to OSHA requirements regarding workplace safety.

• Dallas tx. build new Switch yard for Hitachi power.
• Cable is being pulled throughout the yard, mostly underground, from all transformers to the MCC.
• I installed all cabinets, PLCs, and terminated all inner connections. Installed and routed field cables, knocked out holes for all cables, and stripped and glanded all cables at the PLC.
• Routed fiber optics from panels to the main fiber box, prepped for splicing.
• Walk the job down with the commissioning team. Once the job got approvals, we were able to sign off on work packages.

• Offshore maintenance MP-69 for TPIC.
• I worked mostly out in the MP fields, from changing light bulbs to installing new transformers for living quarters.
• Walk down new jobs for future bidding.
• Hurricane repairs, cable tray installation, lights to be demolished, and compressor repairs.
• Assist the rig electrician with whatever he needs help with.
• Used power construction equipment, measuring devices and testing equipment to complete electrical installations.
• Trained workers to install, maintain and repair electrical equipment and fixtures.
• Worked extensively on three-phase, 277/480 volt power distribution systems.
• Resolved safety issues related to faulty wiring installation practices in a timely manner.
• Followed safety procedures when working on energized circuits; observed lockout and tagout requirements when servicing equipment.
• I did maintenance for Chevron on call in pecos texas. from fixing swapping out fuses to motor swap out.
• Installed Ned JB for flare upgrades, mounted new PLC panels, and routed cable tray, pulled cable to all water and oil tanks for lever switch controls. Most of this work was out of Carlsbad, New Mexico.
• 
  
• Developed accurate estimates and proposals to perform electrical installations and troubleshooting.
• Supervised apprentices and assessed completed tasks, offering guidance and encouragement.
• Fabricated parts according to specifications using hand and power tools.

• Contracted and supervised workers for various construction jobs.
• Resolved labor, design and tool issues during construction projects.
• Prepared and planned worksites to help jobs run smoothly.
• Completed investigations into complaints, incidents and accidents at work sites.
• Utilized spreadsheets, calendars and reports to gauge work productivity and monitor progress.
• Negotiated pricing agreements with vendors based on quantity discounts available.
• Verified work compliance with applicable regulations, codes and specifications.
• Interpreted complex technical documents such as contracts, purchase orders, change orders.
• COVID slowed down jobs, lost funding.