Robert Smith

Worked from ladders, scaffolds and lifts to install, maintain, or repair electrical wiring equipment and lighting fixtures in ceilings, on roofs and on towers.

Planned layout and installation of electrical wiring, equipment, and fixtures.

Inspected electrical systems, equipment and components to identify hazards, defects, and repair requirements.

Used testing instruments such as ohmmeters, voltmeters, ammeters, and multimeters.

Stored and maintained power tools and equipment for each job.

Read and interpreted electrical and mechanical drawings for wiring layouts.

Tested continuity of circuits in electrical wiring, equipment and fixtures.

Fabricated and installed conduit and cable tray.

Pull and terminate wire to breakers, switches, receptacles, CGA's, lights, transmitters, PLC's, Charms and Delta V points.

Hourly Rate $26.50/ hour

Reason for leaving- I'm looking for a more reliable job where I can have a greater opportunity to grow and not worry about running out of work and getting laid off.

Walked down area of damaged steam tracing systems with plant operations.

Gathered and orders parts list needed to repair the steam leaks.

Walked down and locked out the energy isolation point to effected area of repair.

Demo out damaged tubing, piping, valves and steam traps and replaced with new.

Get off lockbox and turn the steam trace on and ensure the problem was resolved.

Hourly Rate $24/ hour

Reason for leaving- My previous employer reached out to me to come back because work had picked back up.

Walked down projects with pre planned packages for maintenance repairs.

Communicate with control room operators for safe work planning.

Gathered proper material to conduct job task.

Measure, cut, thread and install various sizes of conduit and proper supports.

Pull wire to emergency stop switches, motors, CGA's, generators, transmitters.

Labeled and terminate wires.

Installed transmitter enclosure boxes, transmitters, enclosure heaters.

Install pull boxes.

Pull and terminate tubing bundle and heat trace cable.

Perform work task from scaffolds, ladders, scissor lifts and man lifts.

Held meetings, JHA overview and discussed routes to execute safe work.

Properly stored and maintained equipment and power tools.

Inspect harness, hand and power tools.

Comply with all plant safety rules.

Hourly rate $23.90/hour

Reason I left- Work slowed down and got laid off.

Installed, repaired, replaced and maintained heat trace cables, transmitter heaters and heat trace panels.

Ran a crew to perform heat trace installs and audits in power and chemical plants throughout the United States.

Used toners, amp meters, meggers and multimeters to inspect and trouble shoot freeze protection systems.

Installed SR cables, MI cables, tubing bundles and enclosure heaters.

Fabricated and installed cable trays for tubing bundles to transmitters.

Replaced faulty breakers in heat trace panels.

Coordinated with scaffold and insulation crafts, plant maintenance supervisors.

Worked from scaffolds, ladders, scissor lifts, man lifts.

Inspected scaffolds and insulation.

Performed meetings, job plans, and coordinated job scopes.

Documented faulty heat trace and heat trace accessories to plant authorities.

Redlined new heat trace cable installs.

Read and installed new heat trace according to drawings provided.

Installed CEM's bundles from power plant stacks to analyzer buildings.

Hourly rate $32.00/hour

Reason for leaving- I wanted a job that allowed me to be at home more. Job required frequent travel.

Trace out isometric drawings to find correct taps and steam headers for insulated tubing bundle runs.

Determine best routes to installed cable tray and supports for bundle.

Fabricate and install strut and brackets for various size cable trays.

Pull insulated tubing bundles to correct taps and steam headers.

Secure bundles with tie wraps.

Install proper high temp fittings and connect bundles in proper connection points.

Work was performed off of lifts and scaffolds.

Hand and power tools were inspected daily and properly stored and maintained.

Installed self regulating heat trace on process pipes, stripped and terminated cables into terminal blocks in junction boxes.

Conducted meg and ohm test to ensure cables would function properly.

Hourly rate $25.00/hour

Reason for leaving- Project was completed/lay off.

Read and trace out drawings for correct tubing to be installed for steam supply.

Measure, cut and install cable trays for insulated tubing bundles.

Utilize beams and cemented walls for support systems.

Carry, hang and bolt struts and cable trays together in proper routes according to blueprints.

Install tubing to steam headers and process piping to maintain temperature for proper working conditions.

Held daily safety meetings and JSA overviews.

Maintained and erected fabrication areas throughout the plant.

Inspected tools, harnesses, scaffolds and mobile equipment.

Inspected tubing tie in points to ensure tubing was safely secured and ready for start up.

Hourly rate $25.00/hour

Reason for leaving- Project was completed/lay off.

Assigned job daily in person or by phone call the night before.

Arrive as company shop in time to prepare company to with proper material needed to execute job task correctly.

Drive work truck to oil field job site.

Assist work over rigs rig up at oil and gas wells.

Rig up our tools and equipment on work over rig floor.

The rig operator would then pull the various sized tubing from the well, through our equipment which I could read the amount of pitting damage that was done to the pipe from the oil, gas and chemicals ran through the pipe over time.

Based on the readings that showed on my laptop, I would communicate with the operator to either stand the pipe back in the derrick to be later put back in the well or taken out of the well to be replaced with new pipe.

After all pipe had been inspected, I would rig down our equipment, email the documentation to the company man in charge, and return to the shop to clean the truck for thr next well inspection.

Salary rate $3,500/month

Reason for leaving- Oil and gas prices would drop causing lack of work. Wanted a more steady job trade.

Assist shipping supervisor with daily load outs and inspections.

Held morning meetings with safe daily expectations and procedures.

Use computer to acquire list of material needed.

Navigate through warehouse aisle with hand held scanner to check out material and parts needed.

Load all necessary parts into containers, boxes or on pallets to secure safely during shipping transportation.

All boxes, pallets and containers were properly marked with each store they were assigned to go to.

Once everything was picked and packaged, the items would be loaded onto the correct truck in a organized manner for safe delivery to the stores.

Nightly cleaning was done at the end of each shift.

Hourly rate $7.75/hour

Reason for leaving- I wanted to better myself by making more money in a career where I felt more important.