DEREK MORLAN

• This job is ok i want to pursue my career in other ways.
• I would stay with this company but i do not now if they will keep me busy.
• i'am looking for a more permanet position at this time i do not have anything bad to say about them.
• I took this job cause it was the best decision for me at that time.

• I did most of the Instrumentation on this job.i mounted instruments according to where the prints where telling me to put them.
• I also landed a bunch of wires in all different kinds of cabnits.
• I also ran the tubing on this job according to were the prints told me what valves needed tubing instrumentation electrician.

• I was told on this job that there was going to be more work than there actually is.
• We are at the moment just doing grounding and that just consist of digging trenches with a ditch witch or a mini trench they are also doing duct bank work.
• shooting cad weld with cad molds.
• We are running alittle condulet like so prebent six inch ninety's.
• They are conecting to six inch pvc.
• We are also doing the same thing to the two inch.
• instrumentation electrician tri state electric - Edmond, OK.

• I was doing the gas an booster stations around the oklahoma city area for dcp mid streem.
• We bent condulet, pulled wire, terminated wire, pulled wire.
• I aked to do the instrimentation on these jobs but dcp already had someone or there was very little if any.
• instrumentation electrician.

• I started this job as an electrician but by the end of this project i was fitting tubing for instrumentation cause they didn't have anybody who was good enough to fill in they ask me i said i would fill in we bent tubing and cndulet, grounding, pulled wire alittle terminating and installed instruments no trouble shooting.
• i also helped set the cabinets to.
• assembly line hand.

• i was taking a break from the road and spending time with my family.
• I mainly just put trailor truck axels togeather everyday.
• There wasn't any electrical or instrumentation.

• I couldn't find any electrical work at the time and I needed a job and they where hirinig we mainly fit pipe togeather.
• I mad hangers and laid out all the floors so we could just walk bye and hang pipe it was a union job.
• instrumentation electrician.

• I mounted up instrument stands bent condulet, bent tubing, pulled wire, installed instruments, terminated grounds, terminated low voltage cable, and helped to get high voltage cables into mcc room to be terminated.
• instrumentation electrician salusbury industries.

• On this job i bent condulet, bent tubing, pulled wire.
• i did some stick welding on this job but not much.
• i also packed and poured seals.
• I also installed instruments all over the site.
• instrumentation electrician salsbury industries.

• On this job i bent condulet, bent tubing, ran screw pipe for instrument air, ran tubing tray and cable tray helped with some wire pulls and i also got to do some instrument tech work and trouble shooting.
• i also helped with loop checks on start up.

• The short time i was on this job i did the same as I did on the other jobs.
• i bent condulet laid out gutter boxes for panels.
• ran alot of underground condulet for power an for instruments we where running anywhere from 2 inch rob roy condulet all the way down to 1/2 condulet.
• Instrumentation / Elctrictian.

• we where doing maintenance on this job repairing old conduits, wires, control boxes, cabinets, instrument an electrical.
• My crew an myself also replaced instruments, tubing.
• Not only where we replacing old with new but we where also putting in new as well.
• i bent condulet as well as tubing and mounted cabinets, terminated, an pulled wire.
• i took a lot away from this job.

• On this project i was doing both instrumentation an electrical.
• I was bending conduit runs for the instruments i was mounting.
• Then i would pull the wire for the instruments an terminate them.
• i also ran air line with 2 inch screw pipe all the way down to 3/4 inch screw pipe for air line an also bent the tubing.

• This project i was running steam trace on a refinery in Kansas.
• If u dont already know what steam trace is wich im well aware u do but just for your general knowledge if u dont already know what it is, its when u run tubing to fit valve ,pipe really anything u can run tubing to fit ,an it heats it up an keeps it war with steam so it dosent freeze an ruin the product running threw the line.

• i was running security cameras for a trash burning plant in west palm beach.
• It mainly consisted of running conduit , terminating high an low voltage cables, mounting instruments and pulling wire an mounting panels for cables.

• This was more of a commercial environment on this job.
• The job consist of running conduit for light switches an for wall plugs.
• we where going in before they would put up the sheet rock a ruff in our conduit.
• i was bending conduit on this job as well as pulling wire an terminating.
• they where more office rooms i ws ruffing in.

• Basically its like it says i was a maintenance electrician at OU.
• It was a good experience on my part.
• i mainly would change out switches an plugs sometimes on live equipment ,not always.
• we would also do remodels set up for events (that's where the live comes in).
• But for the most part it was just fixing anything that needed fixed.

• ON this project i started out on the electrical side we would bend conduit for lights an some temporary electrical.
• we also ran a lot of cable tray for high an low voltage cables as well as communication for the instruments.
• I also did instrumentation on this job.
• i bent tubing, mounted instruments, fabricated brackets an stands for instruments.
• Run decron tubing to instruments that's insulated tubing.
• i also walked down packages for commissioning an Qc departments.
• i went back to electrical where i bent conduit, pull an terminate wire an also walk down packages for the Electrical department.

Fabricated cable try, hung cable tray, bent rigid conduit,pulled wire, terminated panels, terminated main mcc panels, ran 3/8,1/2, an quarter inch stainless steal tubing, mounted instruments, terminated instruments, had to use location drawings p&id drawing an electrical drawings as well.

Bent 1/4,3/8, an 1/2 inch tubing, mounted instruments, fabricated brackets, stroked valves

It was a turn around so just went around an serviced instruments . We also used heart communicators, took valves out of service an then put them back in service once they put they put the new ones back in. Didn't do to much installs cause it was a turn around it was more work an rerun programs making sure all the instruments where In workin order.

Fabricated cable tray, mounted cable tray, ran 3/4-4 inch rigid conduit, 3/4 emt an 1 inch emt, ran 1/4,3/8, an 1/2 inch tuning, fabricated tubing tray, mounted instruments, pulled wire terminated wire, had to use location drawings, electrical drawings an P&ID drawings, mounted panels, an did some start up on this project

Fabricat stands, mount panels, pull wire, terminate panels, bend 3/4 inch emt - 4 inch emt, 3/4 rigid -4 inch rigid conduit,