Summary
Overview
Work History
Education
Skills
Accomplishments
Certification
Languages
Timeline
Generic

VICTORIA BALLESIL

Union City,USA

Summary

Detail-oriented assembly expert with a proven track record in precision assembly and innovative problem-solving. Proficient in interpreting blueprints, utilizing hand tools, and maintaining high standards of product quality. Committed to fostering team collaboration and driving results while demonstrating reliability and adaptability to meet evolving operational demands. Consistently ensures smooth and efficient workflows, contributing to overall organizational success.

Overview

25
25
years of professional experience
1
1
Certification

Work History

Assembly Technician I

Endologix Medical
07.2024 - 11.2024
  • Building the Stent Grafting
  • Assembled complex medical devices using precision tools and techniques.
  • Conducted quality control inspections to ensure compliance with industry standards.
  • Select the end of the graft that has a tip wire tail closer to the end of the graft.
  • Obtain appropriately sized scalloping (same diameter as heat set mandrel).
  • Slide back heat shrink over the mandrel until the end of the heat shrink is aligned with the edge of the mandrel.
  • Set Heat gun to low heat, and slowly fuse the heat shrink onto the mandrel.
  • Roll cut any heat shrink hanging off the end and slide along the mandrel until one edge is approximately 200mm from one end of the mandrel.
  • Visually inspect the heat shrink for damages. If there are damages, Roll cut heat shrink until all heat shrink on mandrel is smooth.
  • Verify the diameter of scalloping mandrel.
  • Slide graft over the end of the mandrel with the least amount of exposed mandrel.
  • Carefully slide one row of crowns over the heat shrink.
  • Product: Abdominal Aortic Aneurysm (AAA)

Operator II - Robotic and Digital Solution (RAD)

Auris Health, Johnson and Johnson
07.2020 - 05.2024
  • Building the Sheath Shaft Material Handle.
  • Check the Camera/LED - Diode Mode, EM Sensors (Resistance - Ohms) and Continuity wires using the Multimeter.
  • Insert Scope to the Unibody and insert 2 retaining rings.
  • Connect to the Proximal Hub Luer. Wrap around the wires (from the scope) to the Pulley.
  • Secure with upper bearing and secure the bottom using the Quad ring.
  • Secure the Pulley into a unibody. Cover the unibody with the enclosure Dome, then Weld.
  • Check the leak Test.
  • Perform in process inspection.
  • Complete and sign the necessary documents DHR's and daily productivity.
  • Product: Bronchoscopy
  • Certified in Sheath Shaft Material Handle.
  • Certified in Scope Material Handle.

Assembler III

Cerenovus, Johnson and Johnson
11.2004 - 07.2020
  • Product: Aneurysm Catheter
  • Process Certification
  • Coil Line Area
  • Winding Primary wires for Helical and Spherical coils using their specific mandrel.
  • DPU Sub-assembly Area
  • Performing green tubing, winding tip coils, heating, cleaning (using 100% IPA's through Ultrasonic Bath) and cutting tip coils.
  • DPU Line Area
  • Selects appropriate sub-assemblies or component parts and install them in the unit according to design specification.
  • Performing Lamination. Insert PTFE to the hypotube and apply polyamide, then heat into the hotbox.
  • Performing proximal hypotube. Apply Loctite 4310 using EFD dispenser and cure in UV light curing machine.
  • Performing Cutaway. In the Proximal, cut around the extra PTFE and trim the Loctite to be smooth. Testing the HiPot and Resistance using a Multimeter.
  • Complete and sign the necessary documents such as LHR's and daily productivity.
  • Become floater in the different areas in the sub-assembly or in the DPU Line Area. And trained some new assemblers and cross training assemblers.
  • Final Line Area
  • Performing Angle Ring. Apply Loctite 4310 using EFD dispenser and cure in UV light curing machine. Trim the Loctite to be smooth.

Assembler II

Light Connect, Inc.
04.2000 - 06.2004
  • Company Overview: Fiber Optic Company
  • Product: Manufacturer of micro electromechanical system (MEMS)
  • Manufacturer of micro electromechanical system (MEMS) - based components & modules for the fiber optic communication industry.
  • Assembled by die attach, pick and place, wire bonding, soldering and welding.
  • Fiber Optic Company

Education

Bachelor of Science - Business Administration - major in Accounting

University of Baguio
Baguio City, Benguet
01.1984

Skills

  • Medical device manufacturing
  • Precision electronic assembly
  • Chemical knowledge
  • Work order analysis
  • Quality control inspection
  • Component selection for sub-assemblies
  • Wire bonding expertise
  • Welding
  • Precision soldering
  • GDP/GMP Policies
  • Statistical Process Control (SPC)
  • Agile
  • Kanban System
  • Code manufacturing defect records
  • 5S process optimization skills
  • Experience with ISO compliance
  • Kitting assembly

Accomplishments

  • Used Microsoft Excel to develop inventory tracking spreadsheets.

Certification

  • Lamination, sub assemblies, Mechanical assembly - Johnson and Johnson Company (2004 - 2024)

Languages

English
Full Professional
Tagalog
Full Professional

Timeline

Assembly Technician I

Endologix Medical
07.2024 - 11.2024

Operator II - Robotic and Digital Solution (RAD)

Auris Health, Johnson and Johnson
07.2020 - 05.2024

Assembler III

Cerenovus, Johnson and Johnson
11.2004 - 07.2020

Assembler II

Light Connect, Inc.
04.2000 - 06.2004

Bachelor of Science - Business Administration - major in Accounting

University of Baguio

Similar Profiles

CREATE PROFILE